Epoxy.com Product #210100% Solids Coal Tar Epoxy Coating.Solvent Free - Zero (0) VOC Makes it Excellent for Use In Poorly Ventilated AreasDESCRIPTIONEpoxy.com Product #210 Coal Tar Epoxy Coating is a two component, 100% solids coating, especially formulated for high build applications. Epoxy.com Product #210 Coal Tar Epoxy Coating produces a tough, flexible, chemical and impact resistant film. Epoxy.com Product #210 Coal Tar Epoxy Coating is formulated to be easily spray applied, as thick as 40 mils in one coat. Epoxy.com Product #210 Coal Tar Epoxy Coating provides excellent resistance to aggressive water, acids, and caustics. ADVANTAGES
PHYSICAL PROPERTIESEpoxy.com Product #210 Coal Tar Epoxy Coating meets the performance criteria for the American Water Works Association Specification C-210. Since the Product #210 Coal Tar Epoxy Coating is 100% solids, it meets the requirements of the U.S. Environmental Protection Agency's V.O.C. Emission.
SURFACE PREPARATIONAll surfaces to receive Epoxy.com Product #210 Coal Tar Epoxy Coating must be clean and structurally sound, free of dirt, grease, oil, paint, etc. Remove contamination with abrasive blasting, water blasting or wire brush. Make sure all dust is removed after abrasives. Metal should be blasted to SSPC SP-6, 2 to 4 mils profile before coating. Concrete should be blasted or acid etched before coating. Remove all acid with water before coating. MIXINGMix Epoxy.com Product #210 Coal Tar Epoxy Coating at 2A to 3B by volume. Mix well with low speed drill (300 rpm) and Epoxy.com -Mixing Paddle. Stir until uniform, smooth material is seen. Mix minimum of three (3) minutes. Scrape sides and bottom frequently. Avoid entrapping air in mixture. For best results, when spraying, strain material through a 60 mesh screen prior to spraying. APPLICATIONApply Epoxy.com Product #210 Coal Tar Epoxy Coating by brush or spray. Pot Life of Epoxy.com Product #210 Coal Tar Epoxy Coatingis 30 minutes @ 100°F. If heated and sprayed, mix only what you can apply within 30 minutes. Spraying this material requires specialized equipment. Both "A" and "B" Components must be heated to 100°F before spraying. A 45:1 airless spray pump with standard airless spray gun through a .031 to .035 reversible tip is needed. Plural component guns may be used with this product. Higher temperatures and larger masses shorten pot life. PACKAGING5 Gallon Unit = 3 gallons "B" in a 6 gallon pail and 2 gallons "A" in a 2 gallon pail. COVERAGE80 square feet per gallon @ 20 mils. LIMITATIONSDo not use Epoxy.com Product #210 Coal Tar Epoxy Coating below 40°F. Store material under dry conditions. For best results before spraying, rolling, or applying by brush, condition material to 70°F or higher. CAUTION"A" Component—WARNING! Contains epoxy resin. May cause skin irritation or allergic response. Avoid contact with skin. Avoid breathing vapor when heated. In case of skin contact, wash thoroughly with soap and water. In case of ingestion, do not induce vomiting. "B" Component—DANGER! Causes severe burns. Contains alkaline amines. Strong sensitizer. Avoid skin contact. Avoid breathing vapor when heated. Wear protective gloves, goggles and barrier creams. In case of skin contact, wash thoroughly with soap and water. In case of ingestion, induce vomiting. If irritation persists, seek medical attention. FOR INDUSTRIAL USE ONLY.
| ||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2010 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
