Monolithic Waterproofing: Once cured, #417PW allows expansion and contraction over a variety of substrates, including concrete, metal, and wood.

U.V. Stability: #417PW resists exposure to U.V. sun rays and, therefore, is appropriate for exterior applications. Some chalking may occur.

Chemical Resistance: #417PW displays resistance to some liquid chemicals. Specific testing is recommended prior to any installation. Chlorine and other water purification systems are not acceptable. Contact manufacturer for assistance.

Potable Water Lining: PRODUCT #417PW has been designed for use in lining concrete-based above and below grade reservoirs or storage tanks. When #417PW is correctly installed and firmly bonded to the substrate, water cannot flow underneath the lining as is the tendency with sheet lining materials.

Limitations: Containers that have been opened must be used within one or two days since ESI PRODUCT #417PW is a moisture-reactive material. All surfaces must be dry and completely free of foreign matter. This coating will begin to cure when exposed to the humidity in the air.

Shelf Life: 12 months at 77 deg. F. (25C) in tightly sealed containers.

Advantages:

A. ESI PRODUCT #417PW RESERVOIR GRADE is a single-component compound that may be used directly from the container with no mixing required.

B. No catalysts are necessary, as #417PW is a moisture-cured compound.

C. ESI Product #417PW Reservoir Grade Two-Component version, with the non-toxic catalyst, will reduce the tack free time of the coating, thereby, minimizing the likelihood of airborne contaminants or dust from becoming imbedded into the material.

D. Applied cold by spray methods, brush, roller, squeegees or trowel.

E. May be applied over concrete, stone, brick, cement blocks, wood, metal, and most other surfaces.

Concrete substrates require priming with ESI Product #888 Primer. Some substrates may also require priming.

F. ESI PRODUCT #417PW cuts cost of application by eliminating mixing, splicing, sealing tapes, adhesives and other labor consuming methods required when installing other membrane lining systems.

H. ESI PRODUCT #417PW meets standards for use with potable water and does not contain any potentially hazardous coal tar.

Color: Black and White

Standards: A.S.T.M. C836. Conforms to British Standards B.S. 6920 for use in contact with water intended for human consumption. #417PW.

All cracks over 1/16" in width must be filled and covered with ESI PRODUCT #908/909 RESERVOIR GRADE CAULKING. This product may be applied by caulking gun and spatula. There is no need to wait for this product to cure before applying ESI Product #417PW Reservoir Grade since both materials are completely compatible.

A dry film thickness of 60 mils is recommended over concrete and block surfaces. Extremely porous substrates should be filled prior to coating or receive additional ELASTO-DECK B.T. RESERVOIR GRADE.

ESI PRODUCT #417PW RESERVOIR GRADE may be applied by airless spray, roller, brush or squeegee. The first coat of Product #417PWmust be applied at a rate of 40 to 45 square feet per gallon or 30 mils. After a 24 hour cure, apply a second coat of Product #417PWat the same rate of 40 to 45 square feet per gallon to achieve a total dry film thickness of 60 mils. If required, to obtain 90 DFT, repeat after 24 hour cure.

ESI Product #888 Primer must be utilized on concrete substrates at a rate of 300 sq.ft. (27.81 m/2) per gallon.

All products proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control we cannot assume any risk or liability for results obtained, nor can we accept damages in excess of the purchase price of these products. satisfactory results depend not only upon quality products but also upon factors beyond our control; Methods of application and site conditions are examples of such factors and can affect product performance. It is the users responsibility to satisfy himself, by his own information and tests, to determine suitability of the product for his own intended use; User assumes all risks and liability resulting from this use of the product. The substrate must be sound structurally and otherwise. Structural or substrate failures or imperfections resulting in damage to a failure of the coating are not covered by this warranty.