[Epoxy Home] [Catalog of Products] [Where to Start] [Guide Specs] [Epoxy Installation Guides] [Blog Posts] [Epoxy Bonding Systems] [Chip Floors] [Chemical Resistant Epoxy] [Seamless Coatings] [Conductive Epoxy Flooring] [Crack Injection of Concrete & Wood] [Applications] [Elastomeric Polyurethane Systems]  [Seamless Garage Flooring Resins] [High Temperature Epoxy Resins] [Seamless Industrial Floors] [Joint Systems & Sealants] [Methyl Methacrylate MMA ] [Novolac Epoxy Resins] [Epoxy Mortars & Grouts] [Epoxy Novolac] [Primers Sealers] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Epoxy Installation Tips] [Who We Are]  [Epoxy Tech Data Sheets in Acrobat] [Product MSDS Sheets] [Online Order Authorization Form][Contact UsPhone 352.489.1666

  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980Contact Us  

EPOXYSYSTEM’ PRODUCT #451

AROMATIC POLYURETHANE COATING


This Material requires a minimum truckload purchase. Use Product # 467 instead for smaller quantities.

EPOXYSYSTEMS PRODUCT #451 is an aromatic, liquid applied, single-component, moisture cured polyurethane floor coating for use in indoor applications such as industrial plants, mechanical rooms, and locations where surfaces must withstand pedestrian traffic.

PRODUCT DESCRIPTION

Composition: A single component, aromatic based , moisture-cured polyurethane coating.

Basic Uses: EPOXYSYSTEMS PRODUCT #451 is primarily used as a protective top coat of the ELASTO-DECK 5000 M.R. deck coating system. It may also be used as a durable finish that protects interior floors against occasional chemical spillage, dirt, grease and oils. EPOXYSYSTEMS PRODUCT #451 gives floors a well maintained look while retaining a glossy appearance. Dusting of concrete floors is minimized when the surface is sealed with EPOXYSYSTEMS PRODUCT #451. EPOXYSYSTEMS PRODUCT #451 is intended for interior applications only. Coating will discolor if exposed to sunlight.

Limitations: Containers that have been opened must be used up within one or two days since it is a moisture-reactive material. It sets up when exposed to air.

Colors: Concrete Grey, Tan

Sizes: Available in 1 gallon cans, 5 gallon pails and 55 gallon drums.

INSTALLATION

Surface Preparation: EPOXYSYSTEMS PRODUCT #451 may only be applied to dry, clean surfaces. It is recommended to prepare concrete floors by acid-etching or sandblasting. EpoxySystems Product #889 Concrete Primer or EpoxySystems Product #888 Epoxy Concrete Primer may be required prior to applying EPOXYSYSTEMS PRODUCT #451 depending on the concrete substrates condition. All oxidation and rust must be removed from metal surfaces and all metal must be primed with Epoxy.com Product #887 Metal Primer.

Application: EPOXYSYSTEMS PRODUCT #451 may be applied by all conventional means, including spray equipment, paint rollers, and brushes. The rate of application is typically 125 sq. ft. per gallon (3.06 m2/liter). Additional coats may be applied after an overnight cure. It is important not to wait for more than 24 hours before recoating if additional coats are desired. Allow a final cure time of 48 hours before the coating is exposed to traffic.

Caution: An appropriate aggregate, such as aluminum oxide, monterey sand, or other suitable anti-skid material, must be added to the final or next to last coat, in sufficient size and quantity to prevent the coating from being slippery.

PRODUCT WARRANTY

All products proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control we cannot accept damages in excess of the purchase price of these products.

MAINTENANCE

If EPOXYSYSTEMS PRODUCT #451 is damaged, it can be repaired by cleaning the surface with M.E.K. and recoating it with EPOXYSYSTEMS PRODUCT #451 system.

PROPERTY ASTM TEST METHOD RESULTS
Viscosity (at 75OF (24OC) Brookfield Viscometer
Pigmented  35 ± 5 poises
Clear  15 ± 5 poises
Tackfree time (at 75degrees F) (24 degrees C )  6-7 hours
Cure time  24 hours

Weight per gallon

     Pigmented  9.5 lbs.
     Clear  8.5 lbs.

Percent solids ASTM D-2369

     Volume  72%
     Weight  78%
Tensile Strength   ASTM D-412 1900 p.s.i
Percent elongation  ASTM D-412  150%
Tear strength  ASTM D-1004  175 pli
Water Absorption  ASTM D-570  1.70 (% weight change)
Moisture vapor transmission  ASTM E-96

a.) 15 mil dry film (.38mm) 

2.6 perms
b.) 30 mil dry film (.76mm) 1.4 perms
Abrasion Resistance 
CS17 wheel, 1000 revolution,
1000 grams weight
ASTM D-4060  Negligible
Hardness (Shore A)  ASTM D-2240  90
Shelf Life 

6 months in unopened pails
when stored at 77degrees F (25 degree sC)

 

Chemical resistance Resistant 

ASTM D-2299 

to detergent (20%)
5% ammonia, 20% salt solution, anti-freezing agent, paint thinner, 10% hydrochloric acid, 10% sulfuric acid, 50% sodium hydroxide

Hit Counter

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright © 1994-2014 (providing online information about the right product for the right job for 20 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate  and Polyurethanes Six (6) months.  Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products [MSDS in Acrobat Format]  [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter