[Epoxy Home] [Catalog of Products] [Where to Start] [Guide Specs] [Epoxy Installation Guides] [Blog Posts] [Epoxy Bonding Systems] [Chip Floors] [Chemical Resistant Epoxy] [Seamless Coatings] [Conductive Epoxy Flooring] [Crack Injection of Concrete & Wood] [Applications] [Elastomeric Polyurethane Systems]  [Seamless Garage Flooring Resins] [High Temperature Epoxy Resins] [Seamless Industrial Floors] [Joint Systems & Sealants] [Methyl Methacrylate MMA ] [Novolac Epoxy Resins] [Epoxy Mortars & Grouts] [Epoxy Novolac] [Primers Sealers] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Epoxy Installation Tips] [Who We Are]  [Epoxy Tech Data Sheets in Acrobat] [Product MSDS Sheets] [Online Order Authorization Form][Contact UsPhone 352.489.1666

  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980Contact Us  

Epoxy.com Product #6

100% SOLIDS HIGH-MOD GEL ADHESIVE


DESCRIPTION

Epoxy.com Product #6 High-Mod Gel Adhesive is a 100% solids high-mod epoxy gel adhesive used for vertical and overhead bonding applications and structural repairs. It is also used as a grout for anchor bolts, dowels and rebar.

ADVANTAGES

  • Moisture insensitive - makes it more forgiving to cannot dry environments
  • Non-sagging Epoxy Gel Formulation
  • Exceeds requirements for A.S.T.M. C-881-90 Types I,  II, Grade 3, Class "B" and "C"
  • 100% Solids Zero (0) VOC - having no VOC it meets the strictest Low VOC requirements
  • Proven field performance
  • Slower setting - more time to do the job right
  • Waterproof Epoxy Gel

Uses

  • Bonding Hardened Concrete to Hardened Concrete
  • Bonding Wood to Wood
  • Bonding Wood to Concrete
  • Dowel Bar Adhesive
  • Anchor Bolt Adhesive
  • Patching Concrete - horizontal, Vertical and Overhead
  • Patching Wood - horizontal, Vertical and Overhead
  • Setting Injection Ports - for concrete and wood injection
  • Waterproofing

APPLICATION PROCEDURES

Surface Preparation

Before application of gel, surface to be bonded must be clean and sound. Remove all dirt, laitance, grease, curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil-free air blast immediately prior to application.

Mixing Instructions

Temperature of Epoxy.com Product #6 must be 50° F. or above at time of mixing. Stir each component separately, before blending. Mix equal volumes of Part A and Part B for three minutes with a low speed electrical drill equipped with a jiffy mixer or paddle. To prepare a mortar add one part by volume of clean, dry, well graded select sand to one part by volume of mixed epoxy.

Application

To apply Epoxy.com  Product #6 use a spatula, trowel or caulking gun.

Limitations

Use of solvents for thinning Epoxy.com ™ Product #6 will prevent proper cure. Temperature of substrate must be above 40°F. Age of new concrete must be a minimum of 28 days. Maximum thickness per lift for patching application is 1".

SAFETY PRECAUTIONS

Prolonged or repeated exposure may cause eye or skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber or polyethylene gloves.

CLEANING

All tools and equipment should be cleaned before the system gels.Use toluene, Methyl ethyl ketone or any lacquer solvent.

SPECIFICATIONS

APPLICATION PROPERTIES @ 77° F.

Mix Ratio 1:1 by Volume
Gel Time 30 min.
Color Gray
Consistency No Sag
Initial Cure 24 hr. (80% ultimate strength)
Final Cure 7 Days
Coverage @ 30 mils 53 sq. ft./gal
Packaging Gal Cans, 5gal. pails

PHYSICAL PROPERTIES

Bond Strength (Slant Shear) ASTM C 883-78 7 days 3500 P.S.I (34.5 MPa)
Compressive Strength (ASTM C 109 Modified) 12000 P.S.I (82.7 MPa)
Dielectric Strength S/T, Volts per mil 440-465
Tensile Strength @ 75 degrees F (24 degrees C) ASTM D-638 4000 P.S.I (34.5 MPa)
Absorption (ASTM D-570) 0.025%
Shrinkage (ASTM D-2566) Passes Test

Coverage

There are 231 cubic inches to a gallon.  So you will get about 25.6 square feet per 1/16 inch of thickness.  If using this as an anchor bolt, or dowel bar adhesive, you can double check you volume with the Epoxy.com Dowel Bar and Anchor Bolt Adhesive Calculator.

Hit Counter

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright 1994-2014 (providing online information about the right product for the right job for 20 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate  and Polyurethanes Six (6) months.  Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products [MSDS in Acrobat Format]  [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter