600 Flexible Novolac

Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980

EpoxySystems' Product #600

Flexibilized Novolac Epoxy Coating

DESCRIPTION:

PRODUCT #600 Flexibilized Novolac Epoxy Coating is a two-component, 100% solids epoxy coating based on multi-functional high performance flexibilized resin. PRODUCT #600 provides corrosion resistant protection to steel, other metals and concrete. PRODUCT #600 has excellent resistance to chemicals up to 300^oF. PRODUCT #600 is resistant to continuous immersion in water up to 212^oF . PRODUCT #600 is formulated in a convenient 1 to 1 ratio, by volume mix ratio and has a long pot life to simplify application. PRODUCT #600 is more effective in applications which entail force curing.

ADVANTAGES:

WHERE TO USE: For Chemical Protection Of:

	Excellent corrosion barrier properties.
	Excellent chemical resistance.
	Excellent adhesion to most metals.
	It protects concrete, steel, or wood from salts, acids, and alkalies

Steel Tanks	Piping	Heat Exchangers	Condenser Boxes
Hot Water Tanks	Concrete	Manholes

PHYSICAL PROPERTIES:

TYPICAL PROPERTIES PRODUCT #600

Pot Life @ 70-75° F 45-60 min. Pot life after mixing is approximate
Working Time / Application Time @ 70-75° F 35 min.
Cure Time @ 70-75° F Foot Traffic Overnight/16 hrs.
Light Vehicular Traffic 1-2 days
Service 3-7 days
Mix Ratio (by volume) Part A: Part B 1:1
Primer (concrete) Self-Priming
Hardness, Shore D ASTM D 2240 65-80
Tensile Strength, p.s.i ASTM D 638 7 days cure @ 70-75° F 4,000 +
Elongation % @ Break ASTM D 638 7 days cure @ 70-75° F 5-10
Compressive Strength, p.s.i ASTM D 575 10,000+
Impact Strength, in.-lbs. ASTM D 4226 Falling Ball Method 10+
Low Temperature Flexibility ASTM D 3111, 360° Bend 1/4" Mandrel @ -15° F 10 mil thickness Passed

Chemical Resistance

SURFACE PREPARATION:

Steel Surfaces: Steel surfaces should be abrasive blasted to a commercial gray metal finish as specified by the Steel Structures Painting Council SP-6. For immersion service, blast to near white blast SSPC SP-10. Concrete Surfaces: Surface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion. If acid etching is used follow with abrasive or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast, or vacuum, immediately prior to application. See EpoxySystems' Concrete Surface Preparation web page for more details.

MIXING:

Stir Components "A" & "B" thoroughly before mixing. Combine one part by volume of "A" with one part by volume of "B" (mixing ratio 1:1). Mix for not less than three minutes using a slow speed drill (300 to 600 rpm) and EpoxySystems’-Mixing Paddle. Scrape side and bottom to ensure thorough mixing. Avoid entrapping air. Apply immediately after mixing.

APPLICATION:

PRODUCT #600 Flexibilized Novolac Epoxy Coating may be applied by brush, roller, or spray. All spray equipment must employ traps to prevent water and oil from contaminating coating. Thinning may be required for spraying. Heating may be required for spraying. Heating will shorten pot life to 20 minutes at 100^oF. Apply immediately after mixing. Apply 10 mils wet film thickness. Apply topcoat after primer is tack free between 4 and 24 hours. If heated, the tack free time will be reduced.

EpoxySystems’-Fiber Reinforcement is recommend for tank relining. Apply the first coat of PRODUCT #600 then place reinforcement. Work reinforcement into coating. Second coat of PRODUCT #600 is applied after about 3 hours. Be sure to apply second coat within 24 hours of first coat.

COVERAGE:

100-200 square feet per gallon (per coat), dependent upon surface texture and desired thickness. When applying EpoxySystems’-Fiber Reinforcement the coverage will be less.

PACKAGING:

PRODUCT #600 Flexibilized Novolac Epoxy Coating is packaged in 2-gallon and 10-gallon kits.

CAUTION:

WARNING! A Component contains epoxy resin. B Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with eyes or skin. Wear protective clothing, goggles, gloves, and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.

FOR INDUSTRIAL USE ONLY / KEEP AWAY FROM CHILDREN

	Solvent Resistance Good
	Alkali Resistance Excellent
	Acid Resistance Good
	Fuel Oil Excellent

Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826 Technical Support
                         Norm Lambert, President - Technical Support Director
                         info@epoxy.com

352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com

352-489-1625 Fax line to all Departments

www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

[Home] [Up] [600 Flexible Novolac] [630 Novolac Mortar & Coating] [Novolac Joint Filler] [Novolac High Temperature Epoxy] [Novolac Coating] [635 Novolac] [636 High Temp Chemical Resistant Primer/Topcoat] [Multifunctional Epoxy] [643 High Chem Resistant] [648 Chemical Resistant Coating] [670 Vinyl Ester] [Technical Data Sheets in Adobe Acrobat Format][MSDSs in Adobe Acrobat Format][Online- Ordering Authorization Form]

Hit Counter

Secure Login