|
|
EpoxySystems' Product #641LV High Temperature Resistant Epoxy MortarDESCRIPTIONEPOXYSYSTEMS’ PRODUCT #641LV Heat Resistant Epoxy is a two component highly cross-linked novolac epoxy resin system. EPOXYSYSTEMS’ PRODUCT #641LV is especially formulated to be used as a high temperature grouting or laminating resin. It is used to protect concrete, steel and other substrates from high temperatures and corrosion. EPOXYSYSTEMS’ PRODUCT #641LV is 100% solids, has a convenient 2:1 by volume mix ratio, and is easy to apply. ADVANTAGES
USES
PHYSICAL PROPERTIES
CURED PROPERTIES
CURE CYCLEImmersion/Full Chemical and/or heat Exposure 5 days Force cures must be used for enhancement of high temperature and chemical resistant properties or to allow the coating to be placed in service before 5 days. Allow the coating a post cure of 12 to 24 hours before force curing. RECOMMENDED FORCE CURE SCHEDULE CURED: Chemical resistance - acids, alkalies, alcohols, ketones, aromatics and other solvents.SURFACE PREPARATIONConcrete: Remove dirt, loose particles and oil contaminants by scarification, sandblasting, Shotblasting. Vacuum surface before application. Steel: Remove all grease, dirt and other contaminants from surface prior to sandblasting. Grind sharp edges to a radius of 1/8". Remove all weld splatters. Sandblast to a white metal finish according to SSPC-SP-5-63 or NACE standard TM-01-70 with a minimum anchor profile of 3 mils. MIXINGMix 2 parts "A" Component with 1 part "B" Component using a slow-speed drill and EpoxySystems’ - Mixing Paddle for 3-5 minutes. Apply immediately. High temperatures will shorten pot life. APPLICATIONEPOXYSYSTEMS’ PRODUCT #641LV can be applied by brush, roller or trowel. EPOXYSYSTEMS’ PRODUCT #641LV can be applied by trowel or grout pump. EPOXYSYSTEMS’ PRODUCT #641LV is designed as a one coat system (minimum 45 mils, maximum 300 mils). Substrate temperature should be a minimum of 60°F for application to commence. If a second coat is needed before the first coat cures, no surface preparation is needed. Simply apply the second coat maintaining the required standards. However, if the first coat has cured longer than 7 days the first coat must be brush blasted prior to the second coat. COATING: One gallon covers approximately 26.7 ft.2 at 60 mils Grout EPOXYSYSTEMS’ PRODUCT #641LV can be easily made into a heat resistant epoxy grout by adding from 1 to 3 parts by volume of Product #76 Epoxy Extender to the mixed epoxy. 3 gallons EPOXYSYSTEMS’ PRODUCT #641LV + (3) 48 lb. bags #76 = 2,246 cu.in. per unit CLEANING: Clean all equipment immediately after use with MEK or acetone.
CAUTION"A" Component contains epoxy resin . DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.FIRST AID: In case of skin contact, immediately wash with soap and water. in case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing shoes. If irritation persists, seek medical attention. Wash clothing before reuse. KEEP AWAY FROM CHILDREN / FOR INDUSTRIAL USE ONLY |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
