Epoxy.com Epoxy System #9Standard Mortar100% Solids Standard Epoxy Mortar SystemGENERAL DESCRIPTIONEpoxy.com Standard Epoxy Mortar uses 100% solids Epoxy with graded aggregates. Urethane and Epoxy finish coats provide specific performance characteristics as needed Epoxy.com Standard Epoxy Mortar is a resin patching, flooring, and/or repair system consisting of 100% solids epoxy resin and aggregates which provide heavy-duty protection at 3/16" to 1/4". When grouted an sealed, Epoxy.com Standard Epoxy Mortar eliminates porosity and produces a dense, skid-inhibiting finish that will minimize dirt and chemical penetration. Epoxy.com Standard Epoxy Mortar typically uses:
Epoxy.com Standard Epoxy Mortar can also be installed with a conductive system for dispassion of static electricity in areas that are subjected to physical abuse and moderate to heavy wear and impact. Epoxy.com Standard Epoxy Mortar is trowel applied and can be used to form an integral cove base where specified. It has good chemical resistance and is designed for high impact and heavy duty use. Epoxy.com Standard Epoxy Mortar (HP) is the High Performance Mortar exhibiting excellent chemical resistance and utilizes Epoxy.com Product #2 Chemical resistant Resin or Epoxy.com Product #630 Novolac Epoxy for maximum resistance.
Surface PreparationSurface must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, shot blasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast immediately prior to application. ApplicationRoll or squeegee a prime coat. Trowel apply mortar to desired thickness. Grout and Top Coat as needed to achieve required finish and texture. ConsiderationsDo not use in temperatures below 55 degrees F, as cooler temperatures delay hardening. Substrate must be free from hydrostatic pressure, moisture transmission, curing agents and other foreign materials. Urethane seal coats are recommended for areas exposed to intense sunlight. Allow 16 hours for initial set of mortar. Seal Coat time may vary. Safety PrecautionsProlonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves. CLEANINGAll tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent
| ||||||||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2010 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
