DESCRIPTION:
Epoxy.com Product #964 Polymeric Joint Sealant is a two-component
chemically cured polysulfide sealant that provides excellent resistance to
bioactivity and the harsh conditions encountered in wastewater treatment
plants.
Epoxy.com Product #964 Polymeric Joint Sealant cures to a flexible
rubber that provides a watertight seal between concrete, masonry, metals,
glass, wood, and other construction materials. Epoxy.com Product #964
is available in self-leveling. Use Product #965
for a non-sag consistency.
ADVANTAGES:
Epoxy.com Product #964 bonds tightly to most clean, dry surfaces.
Epoxy.com Product #964 provides +/- 25% joint movement in temperatures
as low as -10°F. Epoxy.com Product #964 displays excellent resistance
to heat, ozone, oxidation, sunlight and weathering. Epoxy.com Product
#964 is specially formulated to give resistance to bioactivity and
chemical attack.
PROPERTIES:
Epoxy.com Product #964 has excellent electrical resistance
properties. Typical physical properties of cured material at 77°F (25°C) and
50% relative humidity are as follows:
|
Tensile Strength
|
170 psi
|
|
ASTM D-638
|
1.17 MPa
|
|
Tensile Elongation
|
250%
|
|
ASTM D-638
|
|
Shore Hardness A Scale
|
30-35
|
|
ASTM D-2240
|
|
Service Range
|
-40°F (-40°C) to 250°F (121.1°C)
|
|
Color
|
Gray
|
Pot life after mixing is approximately 40 minutes at 70°F (21.1°C).
Initial cure is 24 hours; final cure is 7 days.
SPECIFICATION:
Epoxy.com Product #964 meet the following specifications:
- National Bureau of Standards and GSA TT-S-0227E (1970)
- American Society for Testing & Materials (ASTM) C-920
- Jet Fuel Resistance Meets Federal
Specification SS-S-200E.
MIXING:
Mix entire contents of "B" Component into "A" with a slow speed
mechanical mixer for 3 minutes. Mix well until color is uniform. Apply
immediately after mixing.
APPLICATION:
Inspect joint slots to assure that they are clean and dry. To maximize
bond to concrete, masonry, and steel, apply Epoxy.com Product #964 Joint
Primer
and allow to dry. Primer must be used in constant immersion joints. Product
#964 may be poured into joint. If you require a gun grade version of this
product use Product #965.
COVERAGE:
Each 1.5 gallon (5.68 L) of mixed material will fill 346 cubic inches
(5.7L) of joint slot, 115 ft. (35 meters) of 1/2" x 1/2" (12 mm x 12 mm) or
57 ft. (17 meters) of 1/2" x 1" (12 mm x 25 mm) joint slot.
PACKAGING:
Epoxy.com Product #964 is available in 1.5 gallon (5.68 L) units.
LIMITATIONS:
Do not install in damp or wet joints. Ambient temperature should be above
40°F (4.4°C) at time of application to assure proper curing.
SHELF LIFE:
One (1) year
CAUTION:
Repeated or prolonged contact with skin should be avoided; protective
gloves should be worn as a precaution. Avoid contact with eyes; in case of
eye contact, flush with water for 15 minutes and consult a physician.
FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.
Untitled Page
Proper mixing and installation is critical to the optimal success of all
product. See Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
375 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2007 EPOXY.COM a
division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy
Systems™ Product Company ("ESI") warrants its products (when properly stored)
for the period of time as follows: Epoxies, Product #315, Product #315BC, and
Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2)
months and Polyurethanes Four (4) months; Power Tools and Equipment 90
days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all
other resins (not specifically mentioned above) 30 days; hand tools (non-power
tools) 30 days. ESI warrants that its products will be free of
manufacturing defects and will be in conformity with published specifications
when handled, stored, mixed and applied in accordance with recommendations of
ESI. If any product fails to meet this warranty, the liability of ESI will be
limited to replacement of any non-conforming material if notice of such
non-conformity is given to ESI within the warranty period for the material (as
indicated above), or within 1 year of the delivery of materials (whichever is
sooner). ESI may in its discretion refund the price received by ESI in lieu of
replacing the material. No customer, distributor, or representative of ESI is
authorized to change or modify the published specifications of this warranty in
any way. No one is authorized to make oral warranties on behalf of ESI. In order
to obtain replacement or refund the customer must provide written notice
containing full details of the non-conformity. ESI reserves the right to inspect
the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED
WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY
UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE
PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY,
WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of
our products are made on an individual order basis. Unless
authorized in writing by Epoxy Systems, Inc. in writing before the material is
made, there are no returns on items purchased from us, once the order has been
processed, and the material made. In the event of authorized returns a
restocking charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on non-list
priced items. All Returns are for merchandise (store) credit only, no cash
or credit card credits. In the event of a return, buyer is responsible for
the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
Secure Login