Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Chemical Resistant Polysulfide Joint Sealant - 2 Component

Product #OSVX573


 

DESCRIPTION:

Product #OSVX573 Polymeric Joint Sealant is a two-component chemically cured polysulfide Picture of Joint Materialsealant that provides excellent resistance to bioactivity and the harsh conditions encountered in wastewater treatment plants. Product #OSVX573 Polymeric Joint Sealant cures to a flexible rubber that provides a watertight seal between concrete, masonry, metals, glass, wood, and other construction materials. Product #OSVX573  has a non-sag consistency.

ADVANTAGES:

Product #OSVX573 bonds tightly to most clean, dry surfaces. Product #OSVX573 provides +/- 25% joint movement in temperatures as low as -10°F. Product #OSVX573 displays excellent resistance to heat, ozone, oxidation, sunlight and weathering. Product #OSVX573 is specially formulated to give resistance to bioactivity and chemical attack.

USES:

Product #OSVX573 is ideal when used as a joint system for:

  • Runways and Tarmacs
  • Jet Fuel Storage Secondary Containment Structures
  • Waste Water Treatment Plants
  • Road Salt Storage Sheds
  • Parking Garages and Driveways
  •  Concrete Swimming Pools
  • Concrete Decks
  • Sidewalks
  • Parking Lots for Aircraft and Automobiles

PROPERTIES:

Product #OSVX573 has excellent electrical resistance properties. Typical physical properties of cured material at 77°F (25°C) and 50% relative humidity are as follows:

Tensile Strength

ASTM D-638

170 psi

1.17 MPa

Tensile Elongation

ASTM D-638

250%

Shore Hardness A Scale

ASTM D-2240

30-35

Service Range

-40°F (-40°C) to 250°F (121.1°C)

Color

Gray

Pot life after mixing at 70°F (21.1°C) approximately 40 minutes
Initial cure 24 hours
Final cure 7 days

SPECIFICATION:

Product #OSVX573 meet the following specifications:

  • National Bureau of Standards and GSA TT-S-0227E (1970)
  • American Society for Testing & Materials (ASTM) C-920
  • Jet Fuel Resistance Meets Federal Specification SS-S-200E.

MIXING:

Mix entire contents of "B" Component into "A" with a slow speed mechanical mixer for 3 minutes. Mix well until color is uniform. Apply immediately after mixing.

APPLICATION:

Inspect joint slots to assure that they are clean and dry. To maximize bond to concrete, masonry, and steel, apply Joint Primer and allow to dry. Primer must be used in constant immersion joints. Apply with either a caulking gun, by trowel, by putty knife, by auto body filer squeegee, or by concrete grout bag, or a follower plate pressurized system.

COVERAGE:

Each 1.5 gallon (5.68 L) of mixed material will fill 346 cubic inches (5.7L) of joint slot, 115 ft. (35 meters) of 1/2" x 1/2" (12 mm x 12 mm) or 57 ft. (17 meters) of 1/2" x 1" (12 mm x 25 mm) joint slot.

PACKAGING:

Product #OSVX573 is available in 1.5 gallon (5.68 L) units.

LIMITATIONS:

Do not install in damp or wet joints. Ambient temperature should be above 40°F (4.4°C) at time of application to assure proper curing.

SHELF LIFE:

6 (six) months.

CAUTION:

Repeated or prolonged contact with skin should be avoided; protective gloves should be worn as a precaution. Avoid contact with eyes; in case of eye contact, flush with water for 15 minutes and consult a physician.

FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.

 Skip Navigation Links

Epoxy.com Home PageExpand Epoxy.com Home Page

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Get important hint, tips, tricks, and product information:  Visit our Blog, and join us on Facebook and Twitter.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2017 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/