|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
Epoxy Mortar Product OverviewEpoxy.com has a large variety of type of mortars. Don't forget that almost all of our 100% resins can be made to double as a mortar, although there handling properties may be less ideal than our actual mortars. Product #10 Lo-Mod Adhesive - a 100% solids Lo-Mod Low Viscosity adhesive used as a binder for epoxy mortar systems in patching and grouting applications, as a seal coat for non-skid surfaces outside, and as a primer to insure high bond strength for coatings and patches. This product can be clear or pigmented for an extra cost. Available in normal, fast, and winter cures. Product #10FAST Lo-Mod Adhesive -Fast Cure Product #10COLD Lo-Mod Adhesive Cold Temperature Cure Product #15 Chemical Resistant Flooring Resin - a two component, seamless 100% solids epoxy resurfacing system with High Chemical Resistance. It may be applied as a coating, or combined with silica sand or EpoxySystems' multi-colored quartz aggregate to produce a durable, easy to maintain floor, on both new and old surfaces. Can also be used to glaze Chip Flooring. Product #16 Epoxy Mortar Resin - a two-component, 100% solids epoxy resin system, mixed at a 1:1 ratio by volume. Epoxy Systems’ Product #16, mixed with up to 3 parts dry EpoxySystems’ Product #75 Filler produces an economical, high-strength epoxy mortar. Product #16 exceeds the requirements of ASTM C-881-78, Grade II, Classes A, B & C, Types I & III. Product #16 is recommended for use in dry environments only. Product #17 Decorative Stone Overlays - a two component, 100% solids high-mod epoxy adhesive used for bonding stone and other aggregates in all types of flooring applications. Some uses would include patios, pool decks, walkways and other areas where a long wearing and decorative system is desired. Product #18 General Purpose Epoxy - a hard set epoxy compound formulated for general use. Product #18 cures at room temperature and is a low viscosity system. This durable, resilient material requires no post curing to achieve permanent bond strength. Mixing ratio of 1 to 1 makes this product easy to use. Product #18 solves many difficult bonding, and epoxy mortar problems. Product has the ability to bond to a variety of substrates including cannot dry and hard to dry surfaces. Product #20 Epoxy Grout - a moisture insensitive, two-component, 100% solids epoxy resin system manufactured specifically for use in temperatures of 40°F and below. It is recommended for injection or anchor-bolt grouting in the neat state or as a mortar when mixed with up to 3 1/4 parts of Product #76 -Epoxy Filler (by volume). PRODUCT #20 exceeds most requirements of ASTM C-881-90, Types I, Grade 1, Class A. Product #21 Pumpable Mortar can be used underwater - a Pumpable Epoxy Mortar that is a moisture insensitive, two-component, 100% solids epoxy resin. This material is specifically designed for use in marine environments, but can be used in wet or dry strippable form applications. #21 can be pumped or poured into the void created between the existing structure and the Epoxy Systems’ Corrosion Free Jacket. Dewatering is not required. Product # 22 Underwater Epoxy Mortar - Pourable Epoxy Mortar that is a moisture insensitive, two-component, 100% solids epoxy resin. This material is specifically designed for use with the Epoxy Systems’ Fiberglass Systems & Shapes. Can also be used as self-leveling flooring. Product #23 - Similar to #22 but in 1:1 mix ratio Product #24 Pigmented Mortar - is a multipurpose colored epoxy binder for EpoxySystems’ Mortar Systems This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas. Available in Normal, Fast, and Winter Cures. Product #24 Fast Pigmented Mortar - Fast Cure Product #24 Cold Pigmented Mortar - Cold Temperature Cure Product #25 Epoxy Mortar Kit standard - a 100% solids epoxy resin and specially selected aggregate system. Units are preproportioned for ease of mixing and use on the jobsite. It is a flowable, self-leveling grout, with handling and physical characteristics superior to similar grouts. Available in Normal, Fast, and Winter Cures. Same as Product #24 Pigmented Mortar but not pigmented. Product #26 Epoxy Mortar Kit - a 100% solids epoxy resin and specially selected aggregate system which produces a flowable, self-leveling grout, with handling and physical characteristics superior to similar grouts. It is designed for floor resurfacing where high strength and short down time are needed. Units are preproportioned for ease of mixing and use on the jobsite. Product #28 Epoxy Mortar - Honey Clear Mortar 4:1 Ratio a multipurpose colored epoxy binder for EpoxySystems’ Mortar Systems This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas. Product #29 Cold Temperature Cure Mortar is a specially formulated binder for cold temperature applications. Able to cure at temperatures as low as 35°F. They are often used in coolers and food preparation areas that require constant low temperatures. Product #29 Cold Temperature Cure EPOXY MORTAR is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs. Product #224 Water Cleanable Epoxy Mortar Resin is a user friendly, water cleanable, 100% solids epoxy grout and adhesive. Used for grouting ceramic tile, brick pavers, and stone, it is supplied in pre-packaged kits containing resin, hardener, and (in the Product #225 Kit) mineral fillers that produce a dense, uniform seal. Typical applications for #224 require resistance to thermal shock, chemicals, and heavy traffic including meat packers, breweries, canneries, bottlers, CIP areas, and pharmaceutical formulators. Product #315 Chip Flooring Product #315 is a seamless, plural component, liquid applied, 100% solids polymeric colored flake floor resurfacing system with superior wear, and chemical resistance. Product #315 with "multi-colored" flakes produces a durable, easy to maintain floor, on both new and old surfaces. Product #453 Elastomeric Mortar - is a sloping system using an elastomeric binder adhesive mixed with aggregate for sloping decks, based on polyurethane elastomers. Product #630 Novolac Coating/Mortar Binder- a 100% solids epoxy Novolac ideal for harsh chemical and solvent resistant applications. It is ideal for use as a troweled mortar, slurry binder, and coating for concrete and steel in extremely corrosive areas where resistance to 98% sulfuric acid or other strong caustics is needed. It is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities.The following mortars have been carefully chosen by EpoxySystems' Tech Support Department as the best for most applications. This is based on there versatility, durability, and favorable handling properties.
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
|
