Product Catalog

 

Here is a quick list of our current product line.  In addition to the products below, we also have hundreds of products which we can "custom" make to your specifications. This page is the most  frequently updatedon our website.  So please check this page often, to see our latest product additions.

 

* Product #1 All Purpose Coating  -  a 100% solids epoxy Hi-Build epoxy coating used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, etc Available in normal, fast, and Cold Temperature Cure versions.
* Product #1Fast  - Shorter Potlife, and faster setting version of Product #1 ,
* Product #1Cold Temperature Cure - This is a version of Product #1 that sets even faster than Product#1 Fast.  Typically used in colder temperatures, or where an very fast cure is required.
* Product #1W a two component, 100% solids epoxy Hi-Build epoxy coating used for high indoor traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, tanks, etc.
* Product #2 Chemical Resistant Coating   - a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications. Available in normal, fast, and Cold Temperature Cure.
* Product #2 Fast  - Shorter Potlife, and faster setting version of Product #2
* Product #2 Cold Temperature Cure  - This is a version of that sets even faster than Product#2 Fast.  Typically used in colder temperatures, or where an very fast cure is required.
* Product #2W a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications.
* Product #3 Injection Resin 3.5:1- a proprietary low viscosity, high modulus, quick strength, epoxy-based binder developed for structurally rebonding cracks, delaminations and hollow planes in Portland cement concrete. Can also be used in certain types of wood injection.  If you are looking for a 2:1 mix ration please see Epoxy.com Product #300-306
* Product #4 Urethane Injection - a one-component, "Acetone Free", MDI based hydrophilic sealing and grouting compound used to stop water leaks in wet environments. Product #4, as it mixes with existing water, cures rapidly into a tough, flexible, closed-cell compound which is insoluble to water and most other chemicals.
* Product #5 Fast Set Gel Adhesive - a 100% solids high-mod epoxy gel adhesive used for vertical and overhead bonding applications and structural repairs. It is also used as a grout for anchor bolts, dowels and rebar.
* Product#6 Gel - Normal Setting Adhesive  - high-mod epoxy gel adhesive used for vertical and overhead bonding applications and structural repairs. It is also used as a grout for anchor bolts, dowels and rebar.
* Product #6SC Long Pot life Adhesive  produces a non-sagging material that is ideal for repairs on vertical or overhead surfaces. PRODUCT #6SC meets or exceeds the requirements of ASTM - C881-87, Types I, II, and IV, Grade 3 Class "B" and "C" 
* Product #7 All Purpose Epoxy Bonding Agent  is a two component, 100% solids epoxy resin system designed to  bond new concrete to old  and other materials to concrete. It has a convenient 1:1 mix ratio, by volume with a viscosity similar to heavyweight oil. It exceeds the requirements of ASTM C-881-90, Types I, II, IV and V, Grade 2, Class "B" and "C".
* Product #7SC - a 100% solids high-mod epoxy adhesive used to bond fresh concrete to cured concrete, steel to fresh or hardened concrete, as a grout for anchor bolts, dowels and rebar, as a binder for epoxy concrete, and for bonding other dissimilar materials. It is similar to Epoxy.com ™ Product #7 but with a slower cure to allow more time for concrete pours.
*  Product #8: Replaced by Product 870 Penetrating Epoxy Sealer)
* Product #9- Lo Mod Mortar Adhesive  -  uses 100% solids Epoxy with graded aggregates. Urethane and Epoxy finish coats provide specific performance characteristics as needed. It is a resin patching, flooring, and/or repair system consisting of 100% solids epoxy resin and aggregates which provide heavy-duty protection at 3/16" to 1/4". When grouted an sealed, Epoxy.com  Epoxy Mortar STD eliminates porosity and produces a dense, skid-inhibiting finish that will minimize dirt and chemical penetration.
* Product #10 Lo-Mod Adhesive- a 100% solids Lo-Mod Low Viscosity adhesive used as a binder for epoxy mortar systems in patching and grouting applications, as a seal coat for non-skid surfaces outside, and as a primer to insure high bond strength for coatings and patches.  
* Product #10FAST Lo-Mod Adhesive  -Fast Cure
* Product #10COLD Lo-Mod Adhesive Cold Temperature Cure
* Product #11 Epoxy Joint Filler - a 100% solids flexible epoxy joint filler for saw-cut joints of concrete slabs on grade, or to repair existing slabs.  Product #11 absorbs the impact and shock of heavy loads and steel wheeled traffic, preventing erosion of control joint edges.
* Product #12 Epoxy Primer - a two component, seamless 100% solids epoxy primer system with High Chemical Resistance and High Bond Strength. The epoxy may be applied as a primer for most High End Industrial coatings, like Epoxies, MMA, Polyurethane's, Vinyl Esters, Polyesters, etc.
* Product #14 Pigmented Mortar -  Replace by Product #24
* Product #15 Chemical Resistant Flooring Resin   - a two component, seamless 100% solids epoxy resurfacing system with High Chemical Resistance. It may be applied as a coating, or combined with silica sand or Epoxy.com  multi-colored quartz aggregate to produce a durable, easy to maintain floor, on both new and old surfaces.
* Product #16 Epoxy Mortar Resin -   a two-component, 100% solids epoxy resin system, mixed at a 1:1 ratio by volume. Epoxy.com Product #16, mixed with up to 3 parts dry Epoxy.com  Product #75 Filler produces an economical, high-strength epoxy mortar. Product #16 exceeds the requirements of ASTM C-881-78, Grade II, Classes A, B & C, Types I & III. Product #16 is recommended for use in dry environments only.
* Product #17 Decorative Stone Overlays -  a two component, 100% solids high-mod epoxy adhesive used for bonding stone and other aggregates in all types of flooring applications. Some uses would include patios, pool decks, walkways and other areas where a long wearing and decorative system is desired. 
* Product #18 General Purpose Epoxy - a hard set epoxy compound formulated for general use. Product #18 cures at room temperature and is a low viscosity system. This durable, resilient material requires no post curing to achieve permanent bond strength. Mixing ratio of 1 to 1 makes this product easy to use. Product #18 solves many difficult bonding, and epoxy mortar problems. Product has the ability to bond to a variety of substrates including cannot dry and hard to dry surfaces.  
* Product #19 Epoxy Mortar a multi-function liquid applied, 100% solids epoxy binder and mortar system with excellent wear, and chemical resistance. Product #19 is an excellent general purpose material with excellent clarity and color retention. It is essentially odorless and so it can be used in occupied areas. 
* Product #20 Epoxy Grout - a moisture insensitive, two-component, 100% solids epoxy resin system manufactured specifically for use in temperatures of 40°F and below. It is recommended for injection or anchor-bolt grouting in the neat state or as a mortar when mixed with up to 3 1/4 parts of Product #76 -Epoxy Filler (by volume). PRODUCT #20 exceeds most requirements of ASTM C-881-90, Types I, Grade 1, Class A.
* Product #21 Pumpable Mortarcan be used underwater - a Pumpable Epoxy Mortar that is a moisture insensitive, two-component, 100% solids epoxy resin. This material is specifically designed for use in marine environments, but can be used in wet or dry strippable form applications. #21 can be pumped or poured into the void created between the existing structure and the Epoxy.com Corrosion Free Jacket. Dewatering is not required.
* Product # 22 Underwater Epoxy Mortar-Pourable Epoxy Mortar that is a moisture insensitive, two-component, 100% solids epoxy resin. This material is specifically designed for use with the Epoxy.com Fiberglass Systems & Shapes. Can also be used as self-leveling flooring.
* Product #23 -  Similar to #22 but in 1:1 mix ratio.  Special order only, with minimum quantities required.
* Product # 24 Pigmented Mortar - is a multipurpose colored epoxy binder for Epoxy.com  Mortar Systems This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas.
* Product # 24 Fast Pigmented MortarFast Cure
* Product # 24 Cold  Pigmented MortarCold Temperature Cure
* Product #25 Epoxy Mortar Kit standard  - a 100% solids epoxy resin and specially selected aggregate system. Units are preproportioned for ease of mixing and use on the jobsite. It is   a flowable, self-leveling grout, with handling and physical characteristics superior to similar grouts.
* Product #26 Epoxy Mortar Kit   a 100% solids epoxy resin and specially selected aggregate system which produces a flowable, self-leveling grout, with handling and physical characteristics superior to similar grouts. It is designed for floor resurfacing where high strength and short down time are needed. Units are preproportioned for ease of mixing and use on the jobsite.
* Product #27 Long PotLife Mortar Kit is a preproportioned 100% solids epoxy resin pack and a blend of special aggregate. The pot life of Product #27 is 3 times longer than ordinary epoxy packs; while curing the entire pack, a low exotherm is produced.
* Product #28 Epoxy Mortar - Honey Clear Mortar 4:1 Ratio a multipurpose colored epoxy binder for Epoxy.com  Mortar Systems This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas.
* Product #29 Cold Temperature Cure Mortar   i  s a specially formulated binder for cold temperature applications. Able to cure at temperatures as low as 35°F. They are often used in coolers and food preparation areas that require constant low temperatures. Product #29 Cold Temperature Cure EPOXY MORTAR is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs.
* Product #30B Cove Mortar Liquid - Special Order.  Minimum Quantities Required.
* Product #30A Cove Mortar Powder - Special Order.  Minimum Quantities Required.
* Product #32 Flexible Epoxy Membrane  is a flexible resin used as an epoxy membrane and as a Product #32 mortar. Epoxy.com  Product #32 is a two component, 100% solids epoxy used as a base in many Epoxy.com  Floor and Mortar Systems. Product #32 resists cracking caused by horizontal substrate movement, providing a crack resistant, resilient, sound absorbent, waterproof, durable floor. Epoxy.com  Product #32 offers stress-relieving properties for floor slabs that show movement or vibration. Product #32 is excellent for use in areas such as mechanical equipment rooms, large animal rooms and activity centers.
* Product # 33 Epoxy Block Filler
* PRODUCT #39 Silane Penetrating Sealer is a one component water based silane that provides excellent protection to concrete surfaces against attack from wet/dry, freeze/thaw cycles, and de-icing chemicals.  PRODUCT #39  imparts a hydrophobic "water-shedding" effect to concrete, masonry, brick, stone & wood surfaces. The water repellency helps reduce cracking spalling, chemical degradation, biological growth, efflorescence, and dirt pick- up.  PRODUCT #39  is easy to use and meets all current VOC regulations.
* Product #40 - Replaced by   PRODUCT #41 Silane Penetrating Sealer
* PRODUCT #41 Silane Penetrating Sealer is a one (1) component sealer that provides excellent protection to concrete against attack from wet/dry, freeze/ thaw cycles, and de-icing chemicals. Epoxy.com  PRODUCT #41 provides a hydrophobic "water-shedding" effect to masonry surfaces. Epoxy.com  PRODUCT #41 is a penetrating sealer that is repellent to liquid water but permeable to water vapor: a "breathable" coating.
* Product #50 Polypropylene Anti-skid Fine
* Product #51 Polypropylene Anti-Skid Course
* Product #52 Polycarbonate  Anti-skid Fine
* Product #53 Polycarbonate Anti-skid Course
* Product #54 Rubber Anti-skid
* Product #63 EVA Expansion Joint -   a water-tight cross-linked closed-cell Ethylene Vinyl Acetate expanded foam material that exhibits unique properties when used in expansion contraction joints. Epoxy.com™ a water-tight cross-linked closed-cell Ethylene Vinyl Acetate expanded foam material that exhibits unique properties when used in expansion contraction joints. Epoxy.com™ Product #63 is water-tight and exhibits good chemical resistance properties to most mild non-oxidizing acids, alkalines and petroleum products.  
* Product #66 Round Quartz Colored Fine   -   a pure silica sand as the basic mineral. Silica is an extremely hard abrasion resistant and chemically inert mineral, ideal for use in conditions that - at times - may be severe. Flooring surfaces produced with high density silica combined with Industrial Flooring Resins produced by us consistently show greater resistance to wear than surfaces filled with minerals or many other resins or binders.
* Product #67 Rounded Quartz Colored Medium  Aggregates - Similar to Product #66, but larger.
* Product #68 Angular Quartz  - Similar to Product #66 but angular.
* Product #69 50% Benzyl Peroxide (BPO) Powder
* Product #71 Fumed Silica Thixotropic Agent
* Product #72 Grade 000 Silica Aggregate
* Product #73 Grade 00 Silica Aggregate
* Product #74 Grade 0 Silica Aggregate
* Product #75 Silica Filler is a very clean, specially graded natural silica aggregate. Product #75 is oven dried just prior to packaging, this makes it suitable for use in epoxy grouts. When mixed with Epoxy.com products, Product #75 makes excellent high strength products .
* Product #76 Epoxy Extender
* Product #77 Broadcast Sand
* Product #78 Self leveling filler
* Product #79 Ground Walnut shell anti-skid aggregate
* Product #80 Acrylic Sealer -  a clear acrylic    solution formulated to create a clear, non-yellowing protective coating. Epoxy.com ACRYLIC SEALER provides a tough, UV and abrasion resistant film that effectively protects surfaces from moisture penetration, staining, dirt, dust, and wear. Providing a surface that is easy to clean and maintain, Epoxy.com ACRYLIC SEALER is an excellent choice for both interior and exterior applications.
* Product #81 Epoxy Gel Extender is a specially formulated blend of fine granules and plasticizers for use with trowelable (thixotropic) epoxy materials.
*  Product #82 Mortar Blend Aggregate 
*  System   #83 Vinyl Ester    -   use in a wide range of industrial applications. Epoxy.com™ VINYL ESTER SYSTEMS can be installed as a coating, slurry, or mortar to meet various chemical and heat resistance needs.
*  Product #84 Universal Primer- Used for EpoxySystems System #83 and many other Epoxy.com  Products
*  Product #85 Vinyl Ester Mortar 
*  Product #86 Vinyl Ester Topcoat
*  Product #87 General Purpose Vinyl Ester
* Epoxy.com  Product #100 uses a unique epoxy technology which allows the contractor to install epoxy systems on new concrete (4-5 days old) without fear of moisture entrapment. Product #100 Exhibits greater than 100 times the permeability of standard epoxy slurries and mortars. Product #100 is used as a base for Epoxy.com  Chip and Quartz systems and as a binder for Epoxy.com  Resinous Mortar Systems, when moisture is a concern.
* Product #105  Concrete Catalyst
* Product #115 Epoxy System for modifying concrete is a two component, 2:1 ratio, 100% solids, liquid epoxy resin system. It can be added to conventional concrete or mortar mixes to produce highfor modifying concrete is a two component, 2:1 ratio, 100% solids, liquid epoxy resin system. It can be added to conventional concrete or mortar mixes to produce high strength, epoxy modified concrete or mortar mix.
* Product #115 Part "C" powder additive for Product #115 Epoxy System - to insure ultimate strength.
* Product #120 is a modified latex liquid admixture to improve the bond of Portland cement concrete toppings, thin-sets, patches, leveling courses, slush coats, stucco; and to improve the "hang" of vertically applied flash coats.
* Product #150 Polyester Grout is a three component, flowable, fast-setting, 100% reactive polyester grout specifically formulated for anchor bolt setting. It may also be used as a grout for floor topping where chemical resistance is required.
* Product #201 Oil Stop Primer for instances petroleum can penetrate the surface of a two component, epoxy-amine undercoating designed to be compatible with petroleum based oil and greases. In many instances petroleum can penetrate the surface of concrete floors to the extent that the oil may not be removed by surface cleaning. If untreated, this oil may migrate back to the surface to cause a delamination.
* Product #203 Cold Temperature Cure Polymeric Primer -t is often used in coolers and food preparation areas that require constant low temperatures. It is frequently used in room temperature applications to meet super-fast cure, limited shutdown needs.  
* Product #204 Cold Temperature Cure Polymeric Coating -   is a specially formulated coating for Product #204 Cold Temperature Cure Polymeric Coating-   is a specially formulated coating for cold temperature applications. Able to cure at temperatures as low as 35°F. It is often used in coolers and food preparation areas that require constant low temperatures. It is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs.  
*  Product #205 Polymeric Flooring Resin  
* Product #206  Cold Temperature Cure Pigmented Polymeric Flooring Resin  is a specially formulated binder for cold temperature applications. Able to cure at temperatures as low as 35°F. It is often used in coolers and food preparation areas that require constant low temperatures. Product #206 Cold Temperature Cure POLYMERIC MORTAR is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs. Is available in clear or colors. 
* Product #210 Coal Tar Epoxy   is a two component, 100% Solids coating especially formulated for high build applications. It produces a tough, flexible, chemical and impact resistant film.  It is formulated to be easily spray applied as thick as 40 mils in 1 coat.  It provides excellent resistance to aggressive water, acids, and caustics. Suitable for intermittent exposure to 300 degrees F.
* Product #211 Polyamide Epoxy Coating -  Ideal for bonding to steel and similar surfaces - Special order only with larger minimum quantities.
*  Product #212 - Anti-Fouling Coating - Special orders in quantity only available.
* Product #213 Decoupage Epoxy is a two component, 100% solids, epoxy resin system. When mixed at a 1:1 ratio, Product #213 provides a decoupage grade epoxy surface for wood products. Product #213 gives a beautiful elegant mar resistant surface that will enhance the look and value of wood for years to come.
* Product #214 Tabletop Resin-    an all-purpose, low viscosity Epoxy System for coating wooden counter tops, tabletops, bar tops and similar applications. It forms a glossy, hard surface, which is resistant to stains. It has excellent clarity and color retention. It is essentially odorless and can therefore be used in occupied areas
* Product #215 Epoxy Polyamine  - a high solids, epoxy-polyamide combination, chemical curing, quick- drying resin system. Product #215 produces a ceramic like coating on masonry, concrete plaster, cement, asbestos board, wood, fiberglass, metal and most other rigid materials. Formulated for applications that require superior adhesion and durability, chemical resistance, corrosive protection, quick cure and easy cleaning. 
* Product #216 Coal Tar Epoxy  is a two component coal tar epoxy coating, black in color, used to protect steel, concrete structures, timber, and other construction materials in corrosive environments. It meets all requirements of Corp. of Engineers C-200, Federal Specification DOD-P-23236 (SHIPS), and SSPC 16-91.
* Product #217 Floor Coating Primer
*  Product #218 Floor Coating Intermediate 
*  Product #219 Floor Coating Top Coat 
* Product #220 Rebar Touch Up Epoxy Coating   is a two component, 70% solids epoxy coating specially manufactured to touch up damage epoxy coated rebar or to coat rebars not previously protected against corrosion. 
* Product #221  Replaced by Product #707 Splash Zone & Under Water Paste
* Product #222 Water Based Epoxy-  Epoxy.com Product #222 WATER BASED EPOXY COATING is a two component 100% reactive water based multifunctional epoxy resin coating. Product #222 is manufactured to produce the utmost in performance in a safe, water borne coating. Product #222 provides excellent resistance to salt intrusion, and excellent adhesion to most common construction substrates. 
* P roduct #223   Clear Water Based Epoxy Curing Compound, Sealer and Bonding Agent    is a two component water based epoxy curing that is used to both cure and seal concrete and to bond freshly placed concrete to existing concrete. It is easily pigmented.
* Product #224 Water Cleanable Epoxy Mortar Resin  is a user friendly, water cleanable, 100% solids epoxy grout and adhesive. Used for grouting ceramic tile, brick pavers, and stone, it is supplied in pre-packaged kits containing resin, hardener, and (in the Product #225 Kit) mineral fillers that produce a dense, uniform seal. Typical applications for #224 require resistance to thermal shock, chemicals, and heavy traffic including meat packers, breweries, canneries, bottlers, CIP areas, and pharmaceutical formulators.
* Product #225 Water Cleanable Epoxy Mortar Kit -  includes Product #224 along with the aggregate.  Mix the three components together for a ready to use system.
*

Product #226Fast Setting Water Based Epoxy  is a Fast Setting Water Based Epoxy Coating is a two component, 100% reactive, water based, multi functional epoxy resin coating. PRODUCT #226 is manufactured to produce the utmost in performance in a safe, water borne coating. PRODUCT #226 provides excellent resistance to salt intrusion, and excellent adhesion to most common construction substrates. Product #226 is VOC Compliant, Fast Curing, and tintable with standard colorants.  It is Internally Flexibilized so it can be applied to metals and plastics.  It is water-reducible and easily applied.  Special order item only.  Requires a minimum quantity.  Contact Epoxy.com  Tech Support for details.

* Product #250 Water Tank Type Coating     is a 100% solids, moisture- insensitive epoxy coating, containing no solvents. It is mixed at a 2:1 ratio, produces a tough, chemical and abrasion-resistant coating for dry or damp concrete, wood or steel surfaces.  
* Product #255 Mastic High Build Epoxy Coating is a 100% solids, moisture-insensitive, epoxy resin system. When mixed at a 1:1 ratio, by volume, it produces an excellent coating for dry or damp concrete, wood or steel surfaces. It iss used on piles, piers, and concrete or steel tanks where concrete or steel needs to be protected from abrasive environments.
*  Product # S-255 - Solvent for thinning Epoxy.com  Product #255
*  Product #256 Impact and Chemical Resistant Epoxy Coating. is a 100% solids epoxy coating specifically formulated and manufactured to produce a tough, impact resistant coating
* PRODUCT #260 Corrosion Resistant Epoxy Protective Primer and Coating   are two-component, 100% solids epoxy coatings based on multi-functional high performance resin and anti-corrosive pigment. PRODUCT #260 is used as a two coat system. PRODUCT #260 provides corrosion resistant protection to steel and other metals. PRODUCT #260 has excellent resistance to chemicals up to 300°F, and hot water resistance at temperatures up to 250°F under continuous immersion. PRODUCT #260 is formulated in a convenient 2 to 1 ratio, by volume mix ratio and has a long pot life to simplify application. The primer is green and the topcoat is blue. (Other colors are available as special order product.) PRODUCT #260 is particularly effective in applications which entail force curing, either as pre-immersion or during immersion service.
* Product #300 3.5:1 Injection Resin - This product is an injection resin with a 3.5:1 mix ratio, designed to be backwardly compatible with certain older designs of injection machines.  See the products 301 to 306 below for 2:1 mix ratio injection resins.
* Product #3012:1Injection Resin, low Modulus  - a 100% solids low viscosity epoxy adhesive used to restore cracked structural concrete by the pressure injection method and to grout cracks in a horizontal plane by gravity.
* Product #301SC  a longer Potlife version of Product #301
* Product #301Cold a faster version of  Product #301 typically used in Cold Temperature Cure applications, or where a very fast set is needed
* Product #302   Injection   a 100% solids low viscosity moisture insensitive epoxy adhesive used to restore cracked structural concrete by the pressure injection method and to grout cracks in a horizontal plane by gravity. 
* Product #303 Low Viscosity a is a two component, 100% solids, moisture insensitive epoxy resin system, mixed at a 2:1 ratio, with a viscosity of light-weight oil. Product #303 exceeds the requirements of ASTM C 881 87, Types I, II, Grade 1, Class "B" and "C". Use neat for grouting damp and dry cracks or as a penetrating sealer on concrete, and wood. May also be mixed with Special Fillers (Products #72-75), to create epoxy mortars. 
* Product #304 Injection Resin and Mortar Binder   is a moisture insensitive, two-component, 100% solids epoxy resin system designed specifically for use in temperatures of 40°F and below. It is recommended for injection or anchor-bolt grouting in the neat state or as a mortar when mixed with up to 3 1/4 parts of PRODUCT #75 Filler (by volume). PRODUCT #304 exceeds requirements of ASTM C-881-90, Types I, Grade 1, Class A.
* Epoxy.com PRODUCT #312 Aliphatic Sprayable Polyurea Coating  is a two component sprayable aliphatic polyurea. It dries in seconds to provide a tough chemical and abrasion resistant coating. As an aliphatic polyurea,  PRODUCT #312  is color fast and will resist yellowing from Ultra violet light exposure. Typical working times of one minute or less can be expected. This fast reaction requires a fast, efficient mixing technique so that the mixture can be applied within the short gel times. Impingement mixing from available two-component spray machinery is efficient and entirely adequate.
*  Product #314 Under Water Coating
* Product #315 Chip Flooring Product #315 is a seamless, plural component, liquid applied, 100% solids polymeric colored flake floor resurfacing system with superior wear, and chemical resistance. Product #315 with "multi-colored" flakes produces a durable, easy to maintain floor, on both new and old surfaces.  
* Product #315BC Polymeric Coating and Base Coat for the  315Chip Flooring System. It can also be used as a stand alone coating. If Epoxy.com Product #315BC is used as a stand alone coating over concrete, it is recommended that you first prime with Product #899 Primer.
* Product #315BC -  Fast  Same as Product #315BC Polymeric Coating for  Base Coat for the 315Chip Flooring System , but with a fast cure.
* Product #315BC-Cold   Same as Product #315BC Polymeric Coating for  Base Coat for the 315Chip Flooring System , but with a cold temperature cure.
*

 Epoxy.com #315NH is a 100%solids, moisture-insensitive epoxy coating. Epoxy.com #315NH mixed at 2 :1 by volume ratio, produces an excellent coating for dry or damp concrete, wood, or steel surfaces. Epoxy.com #315NH is available in a summer grade and winter grade formulation. It can be used as a stand alone coating or as a base coat for Epoxy.com chip floor. It can also be used to replace Product #315BC Polymeric Coating when a non-hazmat to ship basecoat is required.

* Product #316 Fast Set Flooring  -  a 100 % solids fast setting two-component epoxy resin system. Is made to set fast even in temperatures below freezing. It is recommended for flooring, injection or anchor-bolt grouting in the neat state or as a mortar when mixed  #75 Filler . It exceeds most requirements of ASTM C-881-99, Types I and IV , Grade 1, Class A. 
* Product #340 Colored Chips forChip Flooring  
*  PRODUCT #400  Chemical Resistant Urethane  is a two component, chemical resistant, polyurethane coating. The high gloss finish offers excellent abrasion resistance, chemical and stain resistance, and superior color retention.  It can be used equally well on vertical or horizontal surfaces. It is ideal for concrete floors.  It is used as a finish coating option for most Epoxy.com  Flooring Systems.
* Product #407 Aliphatic Traffic Bearing Membrane is a two component, ultra high solids aliphatic polyurethane elastomeric membrane. When applied, it is resilient and accommodates movement in concrete substrates. Epoxy.com Product #407 is used as a top coat traffic bearing membrane or non-skid coating that retains color and physical properties when exposed to harsh UV conditions. Epoxy.com Product #407 is used as a system with Epoxy.com Product #882, and may be applied as the top coat on Epoxy.com Product #409 to maximize cost effectiveness. Epoxy.com Product #407 cures at ambient temperatures and is impermeable to moisture, oils, mild acids, gasoline, and alkalies.
* 409 Traffic Bearing Membrane   is a Resilient Traffic Bearing Membrane    is a 100% solids, ambient cure impermeable elastomer.  PRODUCT #409   is resistant to moisture, oils, mild acids, gasoline, and alkalies.  PRODUCT #409  when applied to concrete or other surfaces, is resilient and accommodates movement in concrete substrates.  PRODUCT #409  is used as a traffic bearing membrane or non-skid coating that retains color and physical properties when exposed to harsh UV conditions. 
* Product #410 replaced by  409 Traffic Bearing Membrane
* Product #420 Urethane Injection or moisture.Epoxy.com  Product #420 reacts with water and expands to form an impermeable HYDROPHOBIC barrier. When reacted and hardened, Epoxy.com  Product #420 is insoluble to water and other aggressive chemicals.
* Product #421 Urethane Injection resin
* Product #422 Replace by Product #420  Urethane Injection resin flexible
* Product #423 Urethane Injection resin
* PRODUCT #424 is a rigid two component closed cell foam impervious to water and moisture. It can be used where structural foam is needed to encapsulate waste or restore the physical properties of timber and other masonry materials. 
* Product #425 is a two component, HCFC-141b/water co-blown rigid polyurethane foam system designed for low-density insulation applications. PRODUCT #425 is typically used for floatation (Boat Foam) inside fiberglass parts. It bonds well to metals, wood and some plastics. This foam system meets Military Specification P-21929B.
* Product #426 Urethane Gel
* Product #427 Urethane Cleaner
* Product #428 Urethane Safety Cleaner
* Epoxy.com  Product #429 Urethane Injection Resin Accelerator is specifically formulated to increase the cure rate of Epoxy.com  Product #4 Urethane Injection Resin. The accelerator liquid is normally used to compensate for cold weather or cold water temperatures.
* System #430  Elastomeric Multi-Colored Decking System is a l iquid-applied, single-component, moisture-cured, polyurethane deck covering system. For waterproofing patios, sundecks, stairways, balconies, etc.  Product #430  can be used on all decks where a skid-resistant, long-lasting, wear-resistant, water-proof surface is required. It may be used on new decks as well as on old concrete decks which are damaged, or cracked. The system is suitable for exterior as well as interior applications in all kinds of climates. The coating retains its elastomeric properties in below freezing weather as well as in very hot climates. 
*  Epoxy.com  PRODUCT #431   is a two component, flame retardant foam especially manufactured to provide a rigid foam with physical properties similar to that of timber or cement grouts, at a convenient one to one ratio, A to B, light black in color.  Product #431  will bond to wet, moist or dry surfaces, even to Plexiglas, with no shrinkage and ample pot life after mixing A & B components.
* Epoxy.com Product #432 is a low viscosity, rapid gelling, hydrophobic grout. Epoxy.com Product #432 is used to seal leaks in cracked concrete, for soil stabilization and for repairing leaking joints in structures. This all-purpose grout is easily mixed with water or stabilizer at a convenient 1 to 1 by volume mix ratio
*  Product #440 Light Stable Deck Membrane
* Epoxy.com  Product # 441  is a two component water-based aliphatic (non-yellowing) polyurethane. It is free of the health and environmental problems normally found in solvent-based urethanes, while maintaining excellent performance properties.  Product # 441  polyurethane provides a matte finish.  Product # 441  has good chemical, stain, and mar resistance. In addition, it’s easy to clean and has excellent color retention under heavy foot traffic. It is a high performance coating for use in a variety of seamless floor and wall coating systems.  Product # 441  eliminates the strong solvent odor normally associated with many high performance materials. It’s ideal for topcoats and finishes that require high abrasion resistance. Typical application areas are clean rooms, hospitals, pharmaceutical facilities, stained concrete, wood floors, and as a seal coat for most Epoxy.com floor and wall coating systems.
* Product #500 Polyester Wood Filler Pine is a two component, wood like polyester filler paste. Quick setting and easy to use. Epoxy.com  Polyester Wood Filler is designed primarily for wood repairs in construction surfaces. Can be used to fill areas of deteriorated concrete (or holes). Also used by model shops for making permanent repairs, fillets, and design changes in the construction of all wood models and patterns. Epoxy.com  Polyester Wood Filler has excellent adhesion to wood, fiberglass, and plaster and can be worked with standard woodworking tools in a quick and convenient manner. 
* Product #501 Polyester Wood Filler Mahogany is a two component, wood like polyester filler paste. Quick setting and easy to use. Epoxy.com  Polyester Wood Filler is designed primarily for wood repairs in construction surfaces. Can be used to fill areas of deteriorated concrete (or holes). Also used by model shops for making permanent repairs, fillets, and design changes in the construction of all wood models and patterns. Epoxy.com  Polyester Wood Filler has excellent adhesion to wood, fiberglass, and plaster and can be worked with standard woodworking tools in a quick and convenient manner. 
* Product #502 Polyester Wood Filler Hardener 1 oz.
* Product #503 Polyester Wood Filler Hardener 4 oz.
* Product #504 Polyester Paste Gray   is a fast-setting industrial filler paste used for manufacturing, fabrication and repair in aircraft, aerospace and other industries having requirements for above normal temperature exposure. Fast and permanent applications are achieved by POLYPASTE. The service temperature of Filler 7 is up to 400 degrees F (205 degrees C). It is used in the construction industry to seal cracks for injection and for patches used on concrete, wood, steel and other suitable construction materials. Excellent machining and finishing results are accomplished by grinding, sanding, scraping, etc. When exposed to elevated temperatures, POLYPASTE has a tendency to darken but does not gas, bubble, or cause any finish distortion. This product does not contain wax and readily bonds to itself and other substrates such as FRP/SMC, hi-temp epoxy molds, aluminum, steel, cast iron, urethane foam parts, etc. POLYPASTE is non-metallic, non-conductive, and non-sparking. 
* Product #505 Polyester Paste Black is a fast-setting industrial filler paste used for manufacturing, fabrication and repair in aircraft, aerospace and other industries having requirements for above normal temperature exposure. Fast and permanent applications are achieved by POLYPASTE. The service temperature of Filler 7 is up to 400 degrees F (205 degrees C). It is used in the construction industry to seal cracks for injection and for patches used on concrete, wood, steel and other suitable construction materials. Excellent machining and finishing results are accomplished by grinding, sanding, scraping, etc. When exposed to elevated temperatures, POLYPASTE has a tendency to darken but does not gas, bubble, or cause any finish distortion. This product does not contain wax and readily bonds to itself and other substrates such as FRP/SMC, hi-temp epoxy molds, aluminum, steel, cast iron, urethane foam parts, etc. POLYPASTE is non-metallic, non-conductive, and non-sparking. 
* Product #540  replace by Product #702
*  Product #541 Polyester Anchor Bolt Adhesive
*  Product #550 Rapid Setting Trowel mortar
*  Product #551 Thin Patch
* Product #600 Flexible Novolac is a two-component, 100% solids epoxy coating based on multi-functional high performance flexibilized resin. PRODUCT #600 provides corrosion resistant protection to steel, other metals and concrete. It has excellent resistance to chemicals up to 300oF.  It is resistant to continuous immersion in water up to 212oF . PRODUCT #600 is formulated in a convenient 1 to 1 ratio, by volume mix ratio and has a long pot life to simplify application. PRODUCT #600 is more effective in applications which entail force curing.
* Product #630 Novolac Coating/Mortar Binder - a 100% solids epoxy Novolac ideal for harsh chemical and solvent resistant applications. It is ideal for use as a troweled mortar, slurry binder, and coating for concrete and steel in extremely corrosive areas where resistance to 98% sulfuric acid or other strong caustics is needed. It   is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities.
* Product #632 Novolac Control Joint Filler   is a 100% solids flexible Novolac epoxy Chemical Resistant joint filler for saw-cut joints of concrete slabs on grade.
* Product #633 Novolac Coatingis a 100% solids epoxy Novolac coating ideal for harsh chemical and solvent resistant applications. Itis used in secondary containment, solvent storage, pump pads, trenches, and other high exposure areas. Itis ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities. Product #633 is commonly used as a seal coat for Epoxy.com  MORTAR SYSTEMS where chemical resistant performance is required. 
* Product #634 Novolac High Temperature Epoxy -   is a 100% solids amine cured epoxy Novolac that is solvent free. Suitable for immersion and non-immersion service particularly in aggressive acid and alkali environments with elevated temperatures.  Epoxy.com Product #634  Novolac High Temperature Resin System produces a tough, chemical resistant coating on concrete, iron and non-iron surfaces. As a low viscosity epoxy Novolac it is suitable for hand or spray application. 
* Product #635 Novolac Coating/Mortar Binder is a high solids epoxy Novolac coating ideal for severe chemical and solvent resistant applications. It is filled with treated ceramic filler to provide improved chemical and thermal shock resistance. Itis ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities. Epoxy.com  Product #635 is commonly used as a seal coat for Epoxy.com  MORTAR SYSTEMS where chemical resistant performance is required.
* Product #636 High Temp Chemical Resistant Primer/Topcoat  a 100% solids amine cured epoxy Novolac that is solvent free. Specifically designed as a Methanol resistant coating. Product #635 is well suited for use in a wide array of aggressive acids, alkalies and organic solvents. It produces a tough, chemical resistant coating on concrete, iron and non-iron surfaces. As a low viscosity epoxy Novolac it is suitable for hand or spray application.
* Product #637 High Temp Coating/Primer is a 100% solids amine cured epoxy Novolac that is solvent free. Suitable for immersion and non-immersion service particularly in aggressive acid environments.  Epoxy.com  Product #637  produces a tough, chemical resistant coating on concrete, iron and non-iron surfaces. As a lower viscosity epoxy Novolac it is suitable as a primer or as a top coating. Excellent against 98% Sulfuric Acid.
*  Product #638 Glass Filled Novolac
* Product #640 Chemical & Heat Resistance is a two component; 100% solids brush, roll or airless spray applied coating designed to provide cavitation, corrosion and erosion resistance to concrete, metallic and nonmetallic surfaces. PRODUCT #640 acts as an inert barrier against extremely harsh environmental factors such as low and high PH, temperature extremes, dry and fluid particulate flow and corrosive chemical attack.
* Product #641High Temp Epoxy   is a moisture-insensitive, two-component, 100% solids epoxy coating. It is especially formulated to protect concrete, steel and wood subject to high temperatures and corrosion.
* Product #641LV High Temp Resistant Mortar is a two component highly cross-linked novolac epoxy resin system. It is especially formulated to be used as a high temperature grouting or laminating resin. It is used to protect concrete, steel and other substrates from high temperatures and corrosion.
* Product #642 Multifunctional High Chemical Resistance Epoxy Coating/Bonder  is a two component, 100% solids, one coat trowel grade or grout pump applied protective coating designed to provide cavitation, erosion and corrosion resistance to metallic and non-metallic surfaces. Product #642 acts as a barrier against extremely harsh environmental factors such as low and high PH, temperatures extremes, dry and fluid particulate flow and corrosive chemical attack.
*  PRODUCT #643    Highly Chemical Resistant Coating  is a solvent free, high functionality Novolac epoxy coating suitable for immersion and non-immersion service. Designed specifically as a Methanol resistant coating.  It is well suited for protection in a wide array of aggressive acids, alkalies and organic solvents. It produces a tough, chemical resistant coating on ferrous and non-ferrous metals and concrete.
* Product #644 High Temp Chemical Resistant Coating. Similar to 641LV, but with fillers to make it thicker.
* 648 Chemical Resistant Coating   is a two component high performance epoxy resin formulated with a convenient 1 to 1 mix ratio. Epoxy.com  PRODUCT #648 Chemical Resistant Coating has been developed as a coating for exposure to organic acids and other severe chemical environments. It is used widely in the food and chemical industries for protection of concrete, wood, and steel. Epoxy.com  PRODUCT #648 is suitable for application by brush, roller or spray. Where in-shop production techniques may be utilized and elevated temperature curing is feasible, rapid property development may be achieved by curing at 200 - 250°F (93 - 121°C). This will provide a cured film which may be handled within a relatively short period of time (about 4 hours). Elevated temperature curing will also enhance ultimate physical and chemical resistant properties.
* Product #650 Resurfacing Grade Epoxy Ceramic Filled Epoxy Coating
* Product #651 Ceramic Filled Epoxy Mortar  is a two-component, 100% solids, ceramic reinforced, trowelable polymeric compound which can be used to repair virtually any metal surface that has been damaged by erosion/corrosion, cavitation or abrasion.
* Product #652 Metal Filled Trowel Grade Epoxy  - a two-component, 100% solids, metal-reinforced polymeric compound which can be used to repair virtually any metal surface that has been damaged, cracked or worn.
* Product #653 Emergency Epoxy Liquid Grade
*  Product #654 Metal Filled Internally lubricated  Trowel Grade
*  Product #669 Strait Vinyl Ester Resin
* Product #670 Vinyl Ester General Purpose is formulated from a vinyl ester, low viscosity resin of 100% reactive solids in a composite with inorganic fiber reinforcement. It provides the ultimate in chemically resistant properties to prevent deterioration where reactive chemicals exist
*   Product #671  Conductive Primer/Sealer -  Epoxy.com  Product #671 is a low viscosity, two component, carbon filled, polyamide modified conductive primer/sealer formulated with special wetting agents to provide maximum penetration into concrete surfaces. Product #671 is ideal for both new and old concrete surfaces. Product #671 provides excellent resistance to wear, and can be used either alone or as a conductive sealer or as a conductive primer when used with Epoxy.com  product #674 Electro-Static Dissipating Urethane Topcoat and Epoxy.com  Conductive Systems.
* Product #672 Conductive Epoxy  is a two component, 100% solids epoxy/aggregate material that utilizes the latest in conductive floor technology. Epoxy.com  CONDUCTIVE EPOXY can be installed as a coating or as a component to Epoxy.com Flooring Systems. It can also include Epoxy.com  ELASTOMERIC MEMBRANES to produce waterproof, crack resistant Systems. Typical Uses of include: Ammunitions Facilities, Paint and Solvent Storage Areas,Electronic Component Plants Hazardous Materials Storage Areas
* Product #673 Conductive Terrazzo
*  PRODUCT #674 - Electrostatic Dissipative Urethane Coating   is a two component, Electro Static Dissipative chemical resistant, polyurethane coating. The high gloss finish offers excellent abrasion resistance, chemical and stain resistance, and superior color retention. Epoxy.com  PRODUCT #674 can be used equally well on vertical or horizontal surfaces. It is ideal for concrete floors and walls in warehouses, storage facilities, aircraft hangars, animal housing, and vehicle maintenance facilities. Available in both clear and pigmented formulations, Epoxy.com  PRODUCT #674 is used as a finish coating option for most Epoxy.com  Flooring Systems.
* Product #675 Electrostatic Dissipating Water Borne Epoxy Topcoat-a pigmented, water emulsion epoxy electro-static dissipative finish designed to have maximum penetration into concrete surfaces to provide high bond strength and adhesion. It has very low odor and can be used in occupied areas as a finish sealer in Thin-Film Electro-Static Dissipative Coating Systems.
* Product #680 MMA Polymer Concrete   is a Polymer Concrete methyl methacrylate (mma) reactive resin is used as a binder to develop polymer concrete which produces extremely high strength and chemical resistance with an abrasion resistant surface. It  is prepackaged and preproportioned for easy mixing and placing at the job site. The liquid polymer and the preproportioned hardener filler is mixed either in the polyethylene bag or in a mortar mixer.
* Product #681 MMA Primer and Sealer for  MMA Polymer Concrete
* Product #685 MMA Crack Healer and Sealer  is for injection repair or as a penetrating crack repair and sealer on concrete. It is a two component Methyl Methacrylate resin system that polymerizes in place. The extremely low viscosity will penetrate into concrete cracks as fine as 0.003 inches.
*  Product #690 All Purpose MMA Primer and Mortar
* Product #701 Flexible Bonder - a two component, 100% solids, mixed at a 1:1 ratio adhesive formulated to give a permanent bond to ceramic, metal, concrete and elastomeric surfaces. It is thixotropic, non-sag, and is easily applied by trowel.
*  Product #702 Traffic Marker and Anchor Bolt Adhesive  is a two component, 1:1 ratio, 100% solids, moisture insensitive epoxy resin system manufactured to bond delineators and traffic markers to median barriers, parapets, and roadways. It is a normal setting adhesive for use in temperatures above 50° F. PRODUCT #702 will bond to steel, concrete, and asphalt. It exceeds the requirements of AASHTO M237 Type IV.
* Product #703 Flexible Gel Adhesive  is a non-sagging material that is ideal for repairs on vertical or overhead surfaces. It exceeds the requirements of ASTM C 881-87, Types I, II, and III Grade 3, Class "B", "C", "E" and "F".
* Product #704 Emergency Epoxy -   is a rapid setting, two component, 1:1 ratio epoxy adhesive. It sets in six minutes and can be put into service in one hour regardless of temperature. It was designed to bond metals, glass, concrete and wood in a matter of minutes .
* Product #706 Heat Resistant Bonder/Mortaris a 100% solids, moisture insensitive epoxy adhesive and repair material. When A and B Components are mixed they produce a gel consistency similar to petroleum jelly, which will not sag or run on a vertical or overhead surface application.
* Product # 707 Splash Zone & Under Water Epoxy  Paste is a moisture-insensitive, two-component, 100% solids epoxy-resin system. When mixed at a 1:1 ratio, by volume, this product produces a paste-like material that is ideal for protection or restoration of concrete, steel and timber piles and other structural elements in marine environments.
  Product #710 Superseded by Epoxy.com  Product #225    
* Product #711  is protective coating designed to provide cavitation, erosion and corrosion resistance to metallic and non-metallic surfaces. Product #711 acts as a barrier against extremely harsh environmental factors such as low and high PH, temperatures extremes, dry and fluid particulate flow and corrosive chemical attack.   
*  Product #712  a two component flexible sealant, formulated to repair leaking electrical equipment and circuit breakers. It bonds tenaciously to ceramics, plastics, metals and most substrates.
* Product #713 Dowel Bar and Anchor Bolt Adhesive    is a two component, thixotropic, fast setting epoxy adhesive. It is specifically formulated with an easy to use, non sag consistency. The special high function resin system allows cure in temperatures as low as 20 F. The non-sagging properties will permit the material to be pumped or gunned into horizontal holes for anchoring rebar or steel bolts. PRODUCT #713 exceeds the requirements of ASTM C 881-90 Types, I, II, Grade 3, Class A
*  Product #714    Precast Segmental Adhesive    is a 100% solids, gelled epoxy adhesive formulated to the requirements of ASTM C-881-90, Type VI, Grade 3, Class D, E, or F. AASHTO M-235-90 duplicates the technical requirements of ASTM -C-881-90.
* Product #720 Cove Base Binder - can be used to install an integral cove base for most Epoxy.com  Flooring Systems, to provide seamless wall to floor protection.
*  Product #800 Water Based High Performance Sealer Concentrate
*  Product #801 Fast Set Acrylic Sealer
* 810 Primer for Polyurea  is a two-component, clear, VOC compliant floor coating. PRODUCT #810 is fast drying and will cure in temperatures as low as 35°F. Its convenient 2A:1B mixing ratio, no induction time and long pot life simplify mixing and application. PRODUCT #810 protects by penetrating concrete or wood and has excellent adhesion to damp concrete, it is an excellent concrete primer.
* Product #824 Concrete Stain and Coating is a one component, water-repellant concrete stain. Epoxy.com  PRODUCT #824 penetrates existing concrete and imparts color and uniformity the surface without affecting the natural texture. Standard colors are white and gray many other colors of concrete are available.  - Special Order Product.  Can be used only on certain projects.  Minimum quantities apply. Contact Epoxy.com Tech Support for details.
* Product #825 Epoxy Floor Sealer is a non-rewettable, polymer emulsion formulated for use with fast or normal setting floor underlayments.
* Product #826 Floor Curing Agent  - Minimum purchase of 10 each 55 gallon drums required.
* Product #830 is a two component modified epoxy system designed to seal concrete and reduce moisture vapor transmission prior to applying finished flooring. Epoxy.com Product #830 has proven to reduce moisture vapor emissions and be resistant to damage from high alkalinity. Epoxy.com Product #830 is an environmentally friendly material containing no hydrocarbons or other solvents making it zero (0) VOC.
*  Product #843 - High Solids Epoxy Primer
* Product #844 Concrete Membrane Deck Primeris a 100% solids, two (2) component polyurethane primer. This thin film primer promotes long term wear and superior adhesion of the Product #409 Resilient Traffic Bearing Membrane. The Product #844 penetrates and seals the surface to allow for a smoother, pinhole free application.
* Product # 845 Penetrant & Prime Coat is a 100 % solids, low viscosity, epoxy primer for use on steel, concrete or wood. The low viscosity and special adhesion promoters make it an excellent penetrant of rusted steel or concrete.  Epoxy.com #845   acts as an inert barrier, resistant to impact, acids, caustics, solvent and thermal shock. The tough water proof surface is excellent for subsequent coatings. 
* Product 850 (50% Solids - Penetrating Epoxy Sealer)- Is replaced by the higher solids Product 870 (65% Solids - Penetrating Epoxy Sealer)
* Product 870 (65% Solids - Penetrating Epoxy Sealer-  is a two-component penetrating epoxy sealer (with very high solids) designed for superior protection of new concrete or for prolonging the serviceability of partially-deteriorated concrete. The sealer is a low to medium viscosity material and is capable of providing an effective membrane barrier to inhibit moisture migration and corrosive chemical penetration. In the cured state Epoxy.com Product #870 allows moisture vapor transmission; it seals off moisture entry but still allows the concrete to breath. When applied to concrete placed and finished in accordance with standards defined in ACI 201 (Guide to Durable Concrete), Product #870 greatly improves wear resistance of the concrete surface, slows down the corrosion of reinforcing steel and adds many years' life to the structure. Product #870 has a solids content of 50% after curing. It may be applied to dry surfaces at temperatures of 40°F (0°C) or above.  
*  Product #877 Zinc Rich Primer - Superseded by - Epoxy.com  Product #1200 Zinc Rich Primer
*  Product #879 Galvanized and Aluminum Primer
*

Epoxy.com Product #882 Concrete Primer Concrete Membrane Deck Primer is a 100% solids, two (2) component polyurethane primer. This thin film primer promotes long term wear and superior adhesion of the Epoxy.com Product #409 Traffic Bearing Membrane Resilient Traffic Bearing Membrane. The Epoxy.com Product #882 Concrete Primer penetrates and seals the surface to allow for a smoother, pinhole free application.

* Product #899 Epoxy Primer - a damp primer the is a 100%  solids Low-Mod Low Viscosity Primer and Sealer. It may be used as a primer for any Epoxy.com ™ product, or as a stand alone sealer.
* Product #900 Polymeric Caulking- Gun Grade is a 2 part chemically cured elastomers. They provide a flexible and watertight seal between concrete, masonry, metals, glass, wood, and other construction materials.  Product #900  (Gun Grade)/  Product #901  (Pourable) are mixed just prior to application. Color is light gray. (Other colors are available on special order.)
* Product #901 Polymeric Joint Sealant - Pourable Grade is a 2 part chemically cured elastomers. They provide a flexible and watertight seal between concrete, masonry, metals, glass, wood, and other construction materials.  Product #900  (Gun Grade)/  Product #901  (Pourable) are mixed just prior to application. Color is light gray. (Other colors are available on special order.)
* Product #1000 fast setting Mortarwith Migratory Corrosion Inhibitor  is a one component trowelable patching mortar designed for overhead and vertical use. Product #1000 is a special blend of fiber reinforced fast setting cement with silica fume, polymeric compounds and aggregates which achieves structural properties in a short time. It is ready to use with just the addition of clean water which activates the modified cement mortar.
* Product #1001 fast setting Fiber Reinforced Mortar - Two Component Fiber Reinforced Mortar  is composed of polymer resin, selected plasticizers, cement, synthetic fibers and aggregates.  Product #1001   is conveniently packaged in a two part unit to produce the ultimate in bond, compressive strength, and impact resistant properties for a repair mortar
* Product #1002 Polymer Modified Mortar
* Product #1003 Feather Patch - one component Polymer Modified cementitious repair mortar that can be used for interior and exterior repairs
* Product #1004 Self Leveling Floor Topping - is a one component copolymer modified cementitious topping. It is ready to use with only the addition of clean water to activate the polymer modified cement topping. It has a special blend of plasticizers to provide zero shrinkage, high flow and bonding properties necessary   for floor topping.
* 1005 Rapid Set  MORTAR    is a non-shrink cementitious blend with exact ratios of graded siliceous aggregates and other ingredients that produce a strong, durable, rapid repair and resurfacing product.  PRODUCT #1005   is easy and fast to use and has excellent durability and workability.  PRODUCT #1005  is ready to use, simply add potable water and mix to desired consistency.  PRODUCT #1005  is specifically formulated and manufactured to meet Maryland DOT Class II, Type II rapid setting mortar or concrete. 
*  Product # 1006 Self leveling Underlayments
*  Product #1007 Polymer Repair Mortar
*  Product #1008 Rapid Hardening Polymer Repair Mortar  is a one component polymer modified, shrinkage-compensated cement-based mortar. It is designed for horizontal concrete surfaces where high early strength gain is required. The blend of special cements, aggregates, fibers and polymers produce a highly durable mortar or concrete in a short time.
* PRODUCT #1009 Repair Mortar is a polymer modified cement-based topping. It is ideal for leveling and or resurfacing distressed, rough and/or uneven concrete floors.It is easy to use. Add potable water at the jobsite.
* Product #1100 Rewetting Adhesion Promoter
*
PRODUCT #1200 Epoxy Organic Zinc Rich Primer   is a two component epoxy primer which provides both barrier and sacrificial protection against steel corrosion. PRODUCT #1200 promotes adhesion, dries rapidly, and can be either shop or field applied.
* Product #1400 fast setting Fiber Reinforced Mortar
* Product #1450 Silica Fume Concrete Additive
* Product #1451 Catalytic Agent for Concrete
* Product #1452 Synthetic Fiber Additive for Concrete
* Product #1501 Orange Peal Mortar Regular Cure
*  Product #1501Fast- Orange Peal Mortar Fast Cure
*  Product #1501Cold- Orange Peal Mortar Cold Temperature Cure
*  Product #1502 Cove Resin
*  Product #1502Fast- Cove Resin Fast Set
*  Product #1502Cold - Cove Resin Cold Temperature Cure
*  Product #1503- Epoxy Mortar Resin with Fly Ash
*  Product #1503 Fast- Epoxy Mortar Resin with Fly Ash, Fast Cure
*  Product #1503Cold - Epoxy Mortar Resin with Fly Ash, Cold Temperature Cure
* Product #1600 Black Pigment Dispersion in Epoxy
* Product #1625 Red Pigment Dispersion in Polyester
* Product #1626 White Pigment Dispersion in Polyester
* Product #1627 Blue Pigment Dispersion in Polyester
* Product #1628 Green Pigment Dispersion in Polyester
* Product #1629 Various Colored Pigment Dispersions in Polyester
* Product #1700 epoxy compound used as an electrical encapsulation material where ease of use and high electrical resistivity are needed. It is a low viscosity, low odor material with a pourable viscosity. It has a convenient 1 to 1 by volume mix ratio and a long pot life. It has a very low exotherm on curing allowing for large parts with extremely low shrinkage.
*  Product #1800 Fast Setting Brushable Polyurea Coating    is a two component brushable aliphatic polyurea. It cures in minutes to provide a tough chemical and abrasion resistant coating. This reaction is very fast, with typical working times of less than 15 minutes. PRODUCT #1800 is recommended for use in areas such as tanks, cooling tower linings, water and wastewater and waterproof deck coatings. It can be used in food and beverage cold storage areas, mechanical rooms, industrial plants, chemical and fertilizer plants, pulp and paper mills and petrochemical facilities.
*  Product #1810 - Elastomeric Polyurea Lining is a two component spray applied polyurea.  It dries in seconds to provide a tough chemical and abrasion resistant surface.  The reaction is very fast. Typical working times (gel times) are less than 30 seconds.  This fast reaction, of course requires a fast, efficient mixing technique so that the mixture can be applied within the short gel times.  Impingement mixing from available two-component spray machinery is efficient and entirely adequate. 
* Product #4240 is a rigid two component closed cell foam impervious to water and moisture. Product #4240 can be used where foam is needed to fill voids in concrete and timber materials. PRODUCT #4240 contains flame retardant and is considered Class B non-burning Foam when tested in accordance to ASTM E-84. 
* Product #5000 Expansion Bearing is composed of an upper unit, a thin, stainless steel plate bonded to a sole plate and a lower unit composed of Teflon bonded to a durable, resilient fiber-free pad. Sliding or translation occurs between the stainless steel and the Teflon while deflection, rotation and load distribution are accommodated by the resilient pad. Complies with AASHTO standards.
* PRODUCT #8100 Underwater Mortar is a non-water separable grout or concrete that requires merely the addition of potable water at the job site and is mixed to the desired consistency. It may then be pumped or poured in water without any wash-out (separation) of the cement paste from other constituents. For a faster setting version use Epoxy.com Product #8101 Underwater Mortar
*

Epoxy.com Product #8101 Underwater Mortar is a rapid hardening mortar designed to be applied underwater.   Epoxy.com Product #8101 is for hand packing or placing.  It contains special agents that hold the matrix together in water (non-water separable).  Epoxy.com Product #8101 Underwater Mortar requires only the addition of mixing water at the job site. For a slower setting version use PRODUCT #8100 Underwater Mortar

* Acrylic Sealer for Terrazzo -  Epoxy.com ACRYLIC SEALER  is a clear acrylic solution formulated to create a clear, non-yellowing protective coating.  Epoxy.com ACRYLIC SEALER  provides a tough, UV and abrasion resistant film that effectively protects surfaces from moisture penetration, staining, dirt, dust, and wear. Providing a surface that is easy to clean and maintain,  Epoxy.com ACRYLIC SEALER  is an excellent choice for both interior and exterior applications.
* Flex Epoxy- Epoxy Membrane - a flexible resin used as an epoxy membrane and as a flexible epoxy mortar. It is a two component, 100% solids epoxy used as a base in many  Flexible Epoxy Floor and Mortar Systems. It resists cracking caused by horizontal substrate movement, providing a crack resistant, resilient, sound absorbent, waterproof, durable floor. It offers stress-relieving properties for floor slabs that show movement or vibration. It is excellent for use in areas such as mechanical equipment rooms, large animal rooms and activity centers.

Injection and Binary Delivery Systems

Misc. Products