Epoxy.com Product #150
Polyester Grout
DESCRIPTION:
Epoxy.com #150 Polyester Grout is a three component, flowable, fast-setting, 100% reactive polyester grout specifically formulated for anchor bolt setting. It may also be used as a grout for floor topping where chemical resistance is required.
ADVANTAGES:
- May be used in temperatures as low as 50°F
- Provides good chemical resistant surface
- Provides fast set, at temperatures above 50°F, allowing it to be put into service quickly.
PHYSICAL PROPERTIES:
|
Compressive Strength |
5,000 psi + 500 @ 2 hours @ 78°F |
Method B |
11,000 psi + 500 @ 3 days @ 78°F |
Tensile Strength |
24 hours - 1,600 psi + 250 |
Shrinkage |
+ 0.2% |
Pot Life |
30 minutes @ 72°F |
Cure Cycle
| 50°F | 70°F | 90°F | |
| Initial | 3 hours | 2 hours | 1 hour |
| Final | 7 days | 7 days | 7 days |
SURFACE PREPARATION:
Anchor Bolt Grouting: Anchor hole or other surface to which EPOXY.COM #150 POLYESTER GROUT is applied must be free of dust, oil, or any other contaminants. Holes drilled with diamond blade will not produce the best sidewall surface condition. For best results, use rotary type percussion equipment.
FLOOR TOPPING: Surfaces to received EPOXY.COM #150 POLYESTER GROUT must be clean, dry, sound, and free from any materials which might interfere with adheason. Sandblasting, acid etching, or scarification are recommended depending upon the surface to be covered.
MIXING:
At the jobsite, open Component "B" containing the filler/hardener. Begin mixing with an Mixing Paddle and slow-speed electric drill. Slowly pour Component "A", the resin, into Component "B". Mix to a uniform gray color, about 2-3 minutes. Add Component "C" and mix for 1-2 minutes. Pour immediately into bolt holes or frame.
APPLICATION:
Polyester Grout: Pour slowly and stop frequently to permit leveling. Slow pouring will also prevent air entrapment.
PACKAGING AND YIELD:
25 lb. unit = 20 lb. filler/hardener packaged in 3.5 gallon pail plus 1/2 gallon resin plus "C" Component yields 300 cu. in./.175 cu.ft.
50 lb. unit = 40 lb. filler/hardener packaged in 5 gallon pail plus 1 gallon resin plus "C" Component yields 600 cu. in./.350 cu.ft.
LIMITATIONS:
Product must be stored below 80°F to prevent polymerization of liquid and loss of activity of powder. The material has a limited shelf life of 3 months.
CAUTION:
LIQUID IS FLAMMABLE. CONTAINS STYRENE MONOMER. DO NOT USE NEAR OPEN FLAME OR WHILE SMOKING. AVOID CONTACT WITH SKIN. CONSULT MATERIAL SAFETY DATA SHEET PRIOR TO USING MATERIAL.
KEEP AWAY FROM CHILDREN
FOR INDUSTRIAL USE ONLY
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact:
Epoxy.com
321-206-1833 Customer Service - Ordering and Order
Status 714-657-3826 Technical Support 352-489-1625 Fax line to all
Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions. [Home] [Up] [General Purpose] [Fast Set Gel Adhesive] [Gel - Normal] [6SC Long Potlife Adhesive] [Wet to Dry] [Slow Cure Wet to Dry] [Anchor Set] [701 Flexible Bonder] [702 Traffic Marker Adhesive] [Flexible Gel Adhesive] [Emergency Epoxy Gel] [705 Adhesive] [706 Heat Resistant Mortar] [707 Under Water Epoxy] [Tile Adhesive] [Novolac Adhesive] [Dowel Bar & Anchor Bolt Adhesive] [Precast Segmental Adhesive] [Traffic Marker Adhesive]
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
|
