 |
Product #1 All Purpose Coating
-
a 100% solids epoxy Hi-Build epoxy coating used
for high foot and light forklift traffic areas where abrasion resistance
is required; for protection against mild corrosion; and as a decorative
waterproof coating for walls, floors, tanks, etc Available in normal,
fast,
and Cold Temperature Cure versions.
|
|
|
Product
#1Fast - Shorter Potlife, and faster setting version of
Product #1 , |
|
|
Product #1Cold Temperature
Cure
- This is a version of Product #1
that sets even faster than Product#1 Fast. Typically used in colder
temperatures, or where an very fast cure is required. |
|
|
Product #1W a two
component,
100% solids epoxy Hi-Build epoxy coating used for high indoor traffic
areas
where abrasion resistance is required; for protection against mild
corrosion;
and as a decorative waterproof coating for walls, tanks, etc. |
|
|
Product #2 Chemical Resistant
Coating
- a two component, 100% solids epoxy chemical resistant coating used to
protect chemical concrete, steel and other structural materials from
non-oxidizing
acids and alkalines for both interior and exterior applications.
Available
in normal, fast, and Cold Temperature Cure. |
|
|
Product
#2 Fast - Shorter Potlife, and faster setting version of
Product #2 |
|
|
Product
#2 Cold Temperature Cure - This is a version of that sets even
faster
than Product#2 Fast. Typically used in colder temperatures, or where
an very fast cure is required. |
|
|
Product #2W a two
component,
100% solids epoxy chemical resistant coating used to protect chemical
concrete,
steel and other structural materials from non-oxidizing acids and
alkalines
for both interior and exterior applications. |
|
|
Product #3 Injection Resin 3.5:1-
a
proprietary low viscosity, high modulus, quick strength, epoxy-based
binder
developed for structurally rebonding cracks, delaminations and hollow
planes
in Portland cement concrete. Can also be used in certain types of wood
injection.
If you are looking for a 2:1 mix ration please see Epoxy.com
Product #300-306 |
|
|
Product #4 Urethane Injection
-
a one-component, "Acetone Free", MDI based hydrophilic sealing and
grouting
compound used to stop water leaks in wet environments. Product #4, as it
mixes with existing water, cures rapidly into a tough, flexible,
closed-cell
compound which is insoluble to water and most other chemicals. |
|
|
Product #5 Fast Set Gel Adhesive
- a 100% solids high-mod epoxy gel adhesive used for vertical and
overhead
bonding applications and structural repairs. It is also used as a grout
for anchor bolts, dowels and rebar. |
|
|
Product#6 Gel - Normal Setting
Adhesive
- high-mod epoxy gel adhesive used for vertical and overhead
bonding
applications and structural repairs. It is also used as a grout for
anchor
bolts, dowels and rebar.
|
|
|
Product #6SC Long Pot life Adhesive
produces a non-sagging material that is ideal for repairs
on vertical or overhead surfaces. PRODUCT #6SC meets or exceeds the
requirements
of ASTM - C881-87, Types I, II, and IV, Grade 3 Class "B" and "C"
|
|
|
Product #7 All Purpose Epoxy
Bonding Agent is a two
component, 100% solids epoxy resin system designed to bond new
concrete
to old and other materials to concrete. It has a convenient
1:1 mix
ratio, by volume with a viscosity similar to heavyweight oil. It exceeds
the requirements of ASTM C-881-90, Types I, II, IV and V, Grade 2, Class
"B" and "C". |
|
|
Product #7SC - a 100%
solids high-mod
epoxy adhesive used to bond fresh concrete to cured concrete, steel to
fresh
or hardened concrete, as a grout for anchor bolts, dowels and rebar, as
a binder for epoxy concrete, and for bonding other dissimilar materials.
It is similar to Epoxy Systems’ ™ Product #7 but with a slower cure to
allow
more time for concrete pours. |
|
|
Product #8:
Replaced by Product 870 Penetrating
Epoxy
Sealer) |
|
|
Product #9- Lo Mod Mortar Adhesive
- uses 100% solids Epoxy with graded aggregates.
Urethane and Epoxy finish coats provide specific performance
characteristics
as needed. It is a resin patching, flooring, and/or repair system
consisting
of 100% solids epoxy resin and aggregates which provide heavy-duty
protection
at 3/16" to 1/4". When grouted an sealed, EpoxySystems' Epoxy Mortar STD
eliminates porosity and produces a dense, skid-inhibiting finish that
will
minimize dirt and chemical penetration. |
|
|
Product
#10 Lo-Mod Adhesive- a
100% solids
Lo-Mod Low Viscosity adhesive used as a binder for epoxy mortar systems
in patching and grouting applications, as a seal coat for non-skid
surfaces
outside, and as a primer to insure high bond strength for coatings and
patches.
|
|
|
Product
#10FAST Lo-Mod Adhesive -Fast
Cure |
|
|
Product
#10COLD Lo-Mod Adhesive Cold
Temperature
Cure |
|
|
Product #11 Epoxy Joint Filler
- a 100% solids flexible epoxy joint filler for saw-cut joints of
concrete
slabs on grade, or to repair existing slabs. Product #11 absorbs the
impact and shock of heavy loads and steel wheeled traffic, preventing
erosion
of control joint edges. |
|
|
Product #12 Epoxy Primer
- a two
component, seamless 100% solids epoxy primer system with High Chemical
Resistance
and High Bond Strength. The epoxy may be applied as a primer for most
High
End Industrial coatings, like Epoxies, MMA, Polyurethane's, Vinyl
Esters,
Polyesters, etc. |
|
|
Product
#14 Pigmented Mortar - Replace by
Product
#24 |
|
|
Product
#15 Chemical Resistant Flooring
Resin
- a two component, seamless 100% solids epoxy resurfacing system with
High
Chemical Resistance. It may be applied as a coating, or combined with
silica
sand or EpoxySystems' multi-colored quartz aggregate to produce a
durable,
easy to maintain floor, on both new and old surfaces. |
|
|
Product
#16 Epoxy Mortar Resin -
a two-component,
100% solids epoxy resin system, mixed at a 1:1 ratio by volume. Epoxy
Systems’
Product #16, mixed with up to 3 parts dry EpoxySystems’ Product #75
Filler
produces an economical, high-strength epoxy mortar. Product #16 exceeds
the requirements of ASTM C-881-78, Grade II, Classes A, B & C, Types I &
III. Product #16 is recommended for use in dry environments only. |
|
|
Product #17 Decorative Stone Overlays
- a two component, 100% solids high-mod epoxy adhesive used for bonding
stone and other aggregates in all types of flooring applications. Some
uses
would include patios, pool decks, walkways and other areas where a long
wearing and decorative system is desired. |
|
|
Product #18 General Purpose
Epoxy
- a hard set epoxy compound formulated for general use. Product #18
cures at room temperature and is a low viscosity system. This durable,
resilient
material requires no post curing to achieve permanent bond strength.
Mixing
ratio of 1 to 1 makes this product easy to use. Product #18 solves many
difficult bonding, and epoxy mortar problems. Product has the ability to
bond to a variety of substrates including cannot dry and hard to dry
surfaces.
|
|
|
Product #19 Epoxy Mortar -
a multi-function
liquid applied, 100% solids epoxy binder and mortar system with
excellent
wear, and chemical resistance. Product #19 is an excellent general
purpose
material with excellent clarity and color retention. It is essentially
odorless
and so it can be used in occupied areas. |
|
|
Product #20
Epoxy
Grout - a moisture insensitive,
two-component,
100% solids epoxy resin system manufactured specifically for use in
temperatures
of 40°F and below. It is recommended for injection or anchor-bolt
grouting
in the neat state or as a mortar when mixed with up to 3 1/4 parts of
Product
#76 -Epoxy Filler (by volume). PRODUCT #20 exceeds most requirements of
ASTM C-881-90, Types I, Grade 1, Class A. |
|
|
Product #21
Pumpable
Mortarcan be used
underwater - a
Pumpable Epoxy Mortar that is a
moisture
insensitive, two-component, 100% solids epoxy resin. This material is
specifically
designed for use in marine environments, but can be used in wet or dry
strippable
form applications. #21 can be pumped or poured into the void created
between
the existing structure and the Epoxy Systems’ Corrosion Free Jacket.
Dewatering
is not required. |
|
|
Product #
22 Underwater
Epoxy Mortar-Pourable
Epoxy Mortar that is a moisture insensitive,
two-component,
100% solids epoxy resin. This material is specifically designed for use
with the Epoxy Systems’ Fiberglass Systems & Shapes.
Can also be used as self-leveling flooring. |
|
|
Product #23 - Similar to #22 but
in 1:1 mix ratio.
Special order only, with minimum quantities required. |
|
|
Product #
24
Pigmented Mortar - is a multipurpose colored epoxy
binder
for EpoxySystems’ Mortar Systems This all purpose epoxy resin is
characterized
as an excellent general purpose material with good clarity and color
retention.
It is essentially odorless and can therefore be used in occupied areas. |
|
|
Product #
24
Fast Pigmented Mortar - Fast Cure |
|
|
Product #
24
Cold Pigmented Mortar - Cold Temperature Cure |
|
|
Product #25
Epoxy
Mortar Kit standard - a 100% solids epoxy resin and
specially
selected aggregate system. Units are preproportioned for ease of mixing
and use on the jobsite. It is
a flowable,
self-leveling grout, with handling and physical characteristics superior
to similar grouts. |
|
|
Product #26
Epoxy
Mortar Kit - This data sheet is here
for reference only. This product has been replaced by its new and
improved version Product #26HP. |
|
|
Product #26HP Epoxy
Mortar Kit - is a high strength, non shrink, 100% solids epoxy
grout. Epoxy Resin and specially formulated aggregate produce a fluid, non
shrink precision grout. Units are preproportioned for ease of mixing and use
on the jobsite. Epoxy.com Product #26HP has superior handling and physical
characteristics when compared to conventional epoxy grouts. |
|
|
Product #27 Long PotLife Mortar Kit is a
preproportioned 100% solids
epoxy resin pack and a blend of special aggregate. The pot life
of Product #27 is 3 times longer than ordinary epoxy
packs; while curing the entire pack, a low exotherm is produced. |
|
|
Product #28 Epoxy Mortar
- Honey
Clear Mortar 4:1 Ratio a multipurpose colored epoxy binder for
EpoxySystems’
Mortar Systems This all purpose epoxy resin is characterized as an
excellent
general purpose material with good clarity and color retention. It is
essentially
odorless and can therefore be used in occupied areas. |
|
|
Product #29 Cold
Temperature
Cure Mortar i s
a specially formulated binder for cold temperature applications. Able to
cure at temperatures as low as 35°F. They are often used in coolers and
food preparation areas that require constant low temperatures. Product
#29
Cold Temperature Cure EPOXY MORTAR is also frequently used in room
temperature
applications to meet super-fast cure, limited shutdown needs. |
|
|
Product #30B Cove Mortar Liquid - Special Order.
Minimum Quantities Required. |
|
|
Product #30A Cove Mortar Powder - Special Order.
Minimum Quantities Required. |
|
|
Product #32 Flexible
Epoxy Membrane is a flexible
resin used as an epoxy membrane and as a Product #32 mortar. Epoxy
Systems'
Product #32 is a two component, 100% solids epoxy used as a base in many
Epoxy Systems' Floor and Mortar Systems. Product #32 resists cracking
caused
by horizontal substrate movement, providing a crack resistant,
resilient,
sound absorbent, waterproof, durable floor. Epoxy Systems' Product #32
offers
stress-relieving properties for floor slabs that show movement or
vibration.
Product #32 is excellent for use in areas such as mechanical equipment
rooms,
large animal rooms and activity centers. |
|
|
Product # 33 Epoxy Block Filler |
|
|
PRODUCT #39 Silane Penetrating
Sealer
is a one component water based silane that provides excellent
protection
to concrete surfaces against attack from wet/dry, freeze/thaw cycles,
and
de-icing chemicals. PRODUCT #39 imparts a hydrophobic
"water-shedding"
effect to concrete, masonry, brick, stone & wood surfaces. The water
repellency
helps reduce cracking spalling, chemical degradation, biological growth,
efflorescence, and dirt pick- up. PRODUCT #39 is easy
to use and
meets all current VOC regulations. |
|
|
Product #40 - Replaced by
PRODUCT
#41 Silane Penetrating Sealer |
|
|
PRODUCT #41 Silane Penetrating
Sealer
is a one (1) component sealer that provides excellent protection to
concrete
against attack from wet/dry, freeze/ thaw cycles, and de-icing
chemicals.
EPOXYSYSTEMS’ PRODUCT #41 provides a hydrophobic "water-shedding" effect
to masonry surfaces. EPOXYSYSTEMS’ PRODUCT #41 is a penetrating sealer
that
is repellent to liquid water but permeable to water vapor: a
"breathable"
coating. |
|
|
Product #50 Polypropylene Anti-skid Fine |
|
|
Product #51 Polypropylene Anti-Skid Course |
|
|
Product #52 Polycarbonate Anti-skid Fine |
|
|
Product #53 Polycarbonate Anti-skid Course |
|
|
Product #54 Rubber Anti-skid |
|
|
Product #63
EVA Expansion
Joint - a water-tight
cross-linked closed-cell Ethylene Vinyl Acetate expanded foam material
that
exhibits unique properties when used in expansion contraction joints.
ESI™
a water-tight
cross-linked closed-cell Ethylene Vinyl Acetate expanded foam material
that
exhibits unique properties when used in expansion contraction joints.
ESI™
Product #63 is water-tight and exhibits good chemical resistance
properties
to most mild non-oxidizing acids, alkalines and petroleum products.
|
|
|
Product #66 Round Quartz Colored Fine
-
a pure silica sand as the basic mineral.
Silica is an extremely hard abrasion resistant and chemically inert
mineral,
ideal for use in conditions that - at times - may be severe. Flooring
surfaces
produced with high density silica combined with
Industrial Flooring Resins
produced
by us consistently show greater resistance to
wear than surfaces filled with minerals or many other resins or binders. |
|
|
Product #67
Rounded
Quartz Colored Medium Aggregates - Similar to Product #66,
but larger. |
|
|
Product #68 Angular Quartz -
Similar to Product
#66 but angular. |
|
|
Product #69 50% Benzyl Peroxide (BPO) Powder |
|
|
Product #71 Fumed Silica
Thixotropic Agent |
|
|
Product #72 Grade 000 Silica Aggregate |
|
|
Product #73 Grade 00 Silica Aggregate |
|
|
Product #74 Grade 0 Silica Aggregate |
|
|
Product #75 Silica
Filler is a very clean, specially
graded natural silica aggregate. Product #75 is oven dried just prior to
packaging, this makes it suitable for use in epoxy grouts. When mixed
with
Epoxy.com products, Product #75 makes excellent high strength
products . |
|
|
Product #76 Epoxy Extender |
|
|
Product #77 Broadcast Sand |
|
|
Product #78 Self leveling filler - is a
specially graded blend of fine dry silica sands, designed as a self
leveling filler for Epoxy.com 100%Solids Epoxy Mortar Products.
It is dried before bagging. Epoxy.com Product #78 works best when being used
with a low viscosity resin like Epoxy.com Product #10 ,
Product #24 and Product #28. The
amount of Product #78 Self-Leveling Epoxy Filler that you add can be varied for
the application. |
|
|
Product #79 Ground Walnut shell anti-skid aggregate |
|
|
Product #80
Acrylic Sealer -
a clear acrylic
solution formulated to create a clear, non-yellowing protective coating.
EPOXY SYSTEMS’ ACRYLIC SEALER provides a tough, UV and abrasion
resistant
film that effectively protects surfaces from moisture penetration,
staining,
dirt, dust, and wear. Providing a surface that is easy to clean and
maintain,
EPOXY SYSTEMS’ ACRYLIC SEALER is an excellent choice for both interior
and
exterior applications. |
|
|
Product #81 Epoxy
Gel
Extender is a specially
formulated blend of fine granules and plasticizers for use with
trowelable
(thixotropic) epoxy materials. |
|
|
Product #82 Mortar Blend Aggregate |
|
|
System
#83 Vinyl Ester
- use in a wide range of industrial
applications. ESI™ VINYL ESTER SYSTEMS can be installed as a coating,
slurry,
or mortar to meet various chemical and heat resistance needs. |
|
|
Product #84
Universal Primer- Used for EpoxySystems System #83 and many other
EpoxySystems'
Products |
|
|
Product #85
Vinyl Ester Mortar |
|
|
Product #86
Vinyl Ester Topcoat |
|
|
Product #87
General Purpose Vinyl Ester |
|
|
EpoxySystems’ Product #100
uses a unique epoxy technology which allows the contractor to
install epoxy
systems on new concrete (4-5 days old) without fear of moisture
entrapment.
Product #100 Exhibits greater than 100 times the permeability of
standard
epoxy slurries and mortars. Product #100 is used as a base for
EpoxySystems’
Chip and Quartz systems and as a binder for EpoxySystems’ Resinous
Mortar
Systems, when moisture is a concern. |
|
|
Product #105 Concrete Catalyst |
|
|
Product #115
Epoxy System
for modifying concrete is a two component, 2:1 ratio, 100% solids,
liquid
epoxy resin system. It can
be added to conventional concrete or mortar mixes to produce highfor
modifying concrete is a two component, 2:1 ratio, 100% solids, liquid
epoxy resin system. It can
be added to conventional concrete or mortar mixes to produce high
strength,
epoxy modified concrete or mortar mix. |
|
|
Product #115 Part "C" powder
additive for
Product #115
Epoxy System
- to insure ultimate strength. |
|
|
Product
#120
is a modified
latex liquid admixture to improve the bond of Portland cement concrete
toppings,
thin-sets, patches, leveling courses, slush coats, stucco; and to
improve
the "hang" of vertically applied flash coats. |
|
|
Product #150 Polyester
Grout is a three component, flowable, fast-setting, 100%
reactive polyester grout specifically formulated for anchor bolt
setting. It may also be used as a grout for floor topping where
chemical resistance is required. |
|
|
Product #201 Oil
Stop Primer
for instances petroleum can penetrate the
surface of
a two component,
epoxy-amine undercoating designed to be compatible with petroleum based
oil and greases. In many instances petroleum can penetrate the surface
of
concrete floors to the extent that the oil may not be removed by surface
cleaning. If untreated, this oil may migrate back to the surface to
cause
a delamination. |
|
|
Product #203 Cold
Temperature Cure Polymeric Primer -t is often used
in coolers and food preparation areas that require constant low
temperatures.
It is frequently used in room temperature applications to meet
super-fast
cure, limited shutdown needs. |
|
|
|
Product #204
Cold
Temperature Cure Polymeric Coating -
is a specially formulated coating for
Product #204 Cold
Temperature Cure Polymeric Coating-
is a specially formulated coating for
cold temperature applications. Able to cure at temperatures as low as
35°F.
It is often used in coolers and food preparation areas that require
constant
low temperatures. It is also frequently used in room temperature
applications
to meet super-fast cure, limited shutdown needs. |
|
|
|
Product #205
Polymeric Flooring Resin |
|
|
|
Product #206 Cold
Temperature Cure
Pigmented Polymeric Flooring Resin is a specially formulated
binder for cold temperature applications. Able to cure at temperatures
as
low as 35°F. It is often used in coolers and food preparation areas that
require constant low temperatures. Product #206 Cold Temperature Cure
POLYMERIC
MORTAR is also frequently used in room temperature applications to meet
super-fast cure, limited shutdown needs. Is available in clear or
colors. |
|
|
Product #210 Coal Tar Epoxy
is
a two component, 100% Solids coating especially formulated for high
build
applications. It produces a tough, flexible, chemical and impact
resistant
film. It is formulated to be easily spray applied as thick as 40 mils
in 1 coat. It provides excellent resistance to aggressive water, acids,
and caustics. Suitable for intermittent exposure to 300 degrees F. |
|
|
Product
#211 Polyamide Epoxy Coating - Ideal for bonding to steel and
similar
surfaces - Special order only with larger minimum quantities. |
|
|
Product #212
- Anti-Fouling Coating - Special orders in quantity only available. |
|
|
Product #213 Decoupage Epoxy is
a two component, 100% solids,
epoxy resin system. When mixed at a 1:1 ratio, Product
#213 provides a decoupage grade epoxy surface for wood
products.
Product #213 gives a beautiful elegant mar resistant
surface that will
enhance the look and value of wood for years to come. |
|
|
Product #214
Tabletop Resin-
an all-purpose, low viscosity Epoxy System for
coating wooden counter tops, tabletops, bar tops and similar
applications.
It forms a glossy, hard surface, which is
resistant
to stains. It has excellent clarity and color
retention. It is essentially odorless and can therefore be used in
occupied
areas |
|
|
Product #215
Epoxy Polyamine
- a high solids, epoxy-polyamide combination,
chemical curing, quick- drying resin system. Product #215 produces a
ceramic
like coating on masonry, concrete plaster, cement, asbestos board, wood,
fiberglass, metal and most other rigid materials. Formulated for
applications
that require superior adhesion and durability, chemical resistance,
corrosive
protection, quick cure and easy cleaning. |
|
|
Product #216 Coal
Tar Epoxy
is a two component coal tar epoxy coating, black
in color, used to protect steel, concrete structures, timber, and other
construction materials in corrosive environments. It meets all
requirements
of Corp. of Engineers C-200, Federal Specification DOD-P-23236 (SHIPS),
and SSPC 16-91. |
|
|
Product #217 Floor Coating Primer |
|
|
Product
#218 Floor Coating Intermediate |
|
|
Product
#219 Floor Coating Top Coat |
|
|
Product #220 Rebar Touch Up
Epoxy Coating
is a two component, 70% solids epoxy coating
specially manufactured to touch up damage epoxy coated rebar or to coat
rebars not previously protected against corrosion. |
|
|
Product #221 Replaced by
Product #707 Splash Zone & Under
Water
Paste |
|
|
Product
#222 Water
Based Epoxy- Epoxy Systems’ Product #222
WATER BASED EPOXY COATING is a two component 100% reactive water based
multifunctional
epoxy resin coating. Product #222 is manufactured to produce the utmost
in performance in a safe, water borne coating. Product #222 provides
excellent
resistance to salt intrusion, and excellent adhesion to most common
construction
substrates. |
|
|
P roduct #223
Clear
Water Based Epoxy Curing Compound, Sealer and Bonding Agent
is a two component water based epoxy curing that is used to both cure
and
seal concrete and to bond freshly placed concrete to existing concrete.
It is easily pigmented. |
|
|
Product #224 Water Cleanable Epoxy
Mortar
Resin is a user friendly, water
cleanable, 100% solids epoxy grout and adhesive. Used for grouting
ceramic
tile, brick pavers, and stone, it is supplied in pre-packaged kits
containing
resin, hardener, and (in the Product #225 Kit) mineral fillers that
produce
a dense, uniform seal. Typical applications for #224 require resistance
to thermal shock, chemicals, and heavy traffic including meat packers,
breweries,
canneries, bottlers, CIP areas, and pharmaceutical formulators. |
|
|
Product #225 Water Cleanable Epoxy
Mortar
Kit - includes Product #224 along
with the
aggregate. Mix the three components together for a ready to use system. |
|
|
Product #226Fast
Setting Water Based Epoxy is a Fast Setting Water Based
Epoxy
Coating is a two component, 100% reactive, water based, multi functional
epoxy resin coating. PRODUCT #226 is manufactured to produce the utmost
in performance in a safe, water borne coating. PRODUCT #226 provides
excellent
resistance to salt intrusion, and excellent adhesion to most common
construction
substrates. Product #226 is VOC Compliant, Fast Curing, and tintable
with
standard colorants. It is Internally Flexibilized so it can be applied
to metals and plastics. It is water-reducible and easily applied.
Special order item only. Requires a minimum quantity. Contact
EpoxySystems' Tech Support for
details.
|
|
|
|
|
Product #250 Water Tank Type
Coating
is a 100% solids,
moisture- insensitive epoxy coating, containing no solvents. It is mixed
at a 2:1 ratio, produces a tough, chemical and abrasion-resistant
coating
for dry or damp concrete, wood or steel surfaces. |
|
|
Product #255 Mastic High
Build Epoxy
Coating is a 100% solids, moisture-insensitive, epoxy
resin system.
When mixed at a 1:1 ratio, by volume, it produces an excellent coating
for
dry or damp concrete, wood or steel surfaces. It iss used on piles,
piers,
and concrete or steel tanks where concrete or steel needs to be
protected
from abrasive environments. |
|
|
Product # S-255
- Solvent for thinning EpoxySystems' Product #255 |
|
|
Product #256
Impact and Chemical Resistant Epoxy Coating. is a 100%
solids epoxy coating specifically formulated and manufactured to produce
a tough, impact resistant coating |
|
|
PRODUCT #260 Corrosion
Resistant Epoxy Protective Primer and Coating
are two-component, 100% solids epoxy coatings based on
multi-functional high performance resin and anti-corrosive pigment.
PRODUCT
#260 is used as a two coat system. PRODUCT #260 provides corrosion
resistant
protection to steel and other metals. PRODUCT #260 has excellent
resistance
to chemicals up to 300°F, and hot water resistance at temperatures up to
250°F under continuous immersion. PRODUCT #260 is formulated in a
convenient
2 to 1 ratio, by volume mix ratio and has a long pot life to simplify
application.
The primer is green and the topcoat is blue. (Other colors are available
as special order product.) PRODUCT #260 is particularly effective in
applications
which entail force curing, either as pre-immersion or during immersion
service. |
|
|
Product #300 3.5:1 Injection
Resin - This product is an injection
resin
with a 3.5:1 mix ratio, designed to be backwardly compatible with
certain
older designs of injection machines. See the products 301 to 306 below
for 2:1 mix ratio injection resins. |
|
|
Product #3012:1Injection
Resin, low Modulus - a 100% solids low
viscosity
epoxy adhesive used to restore cracked structural concrete by the
pressure
injection method and to grout cracks in a horizontal plane by gravity. |
|
|
Product #301SC a longer Potlife
version of
Product #301 |
|
|
Product #301Cold a faster version of
Product #301 typically used in
Cold
Temperature Cure applications, or where a very fast set is needed |
|
|
Product
#302
Injection a 100% solids low viscosity moisture
insensitive epoxy adhesive used to restore cracked structural concrete
by
the pressure injection method and to grout cracks in a horizontal plane
by gravity. |
|
|
Product #303
Low Viscosity a is a two
component, 100% solids, moisture insensitive epoxy resin system, mixed
at
a 2:1 ratio, with a viscosity of light-weight oil. Product #303 exceeds
the requirements of ASTM C 881 87, Types I, II, Grade 1, Class "B" and
"C".
Use neat for grouting damp and dry cracks or as a penetrating sealer on
concrete, and wood. May also be mixed with Special Fillers (Products
#72-75),
to create epoxy mortars. |
|
|
Product #304 Injection Resin and
Mortar
Binder
is a moisture insensitive, two-component,
100% solids epoxy resin system designed specifically for use in
temperatures
of 40°F and below. It is recommended for injection or anchor-bolt
grouting
in the neat state or as a mortar when mixed with up to 3 1/4 parts of
PRODUCT
#75 Filler (by volume). PRODUCT #304 exceeds requirements of ASTM
C-881-90,
Types I, Grade 1, Class A. |
|
|
Product #305 Injection Resin
200 CPS - Epoxy.com Products #305 and Product #306
are two-component, low viscosity, 100% solids epoxy resin base adhesive.
Modified Bisphenol A-Epichlorohydrin epoxy resin and Amido-amine type
hardener,
modified to be compatible with damp concrete. Product #305 has a Potlife
of 1 hour at 77° F (25° C). |
|
|
Product #306 Injection Resin
is a fast version of Product #305. Product #306
has a pot life of 5-10 minutes at 77° F (25° C) |
|
|
Epoxy.com
PRODUCT #312 Aliphatic Sprayable Polyurea Coating
is a two component sprayable aliphatic polyurea.
It dries in seconds to provide a tough chemical and abrasion resistant
coating.
As an aliphatic polyurea, PRODUCT #312 is color fast
and will resist
yellowing from Ultra violet light exposure. Typical working times of one
minute or less can be expected. This fast reaction requires a fast,
efficient
mixing technique so that the mixture can be applied within the short gel
times. Impingement mixing from available two-component spray machinery
is
efficient and entirely adequate. |
|
|
Product #314
Under Water Coating |
|
|
Product #315
Chip Flooring Product #315
is a seamless, plural component, liquid applied, 100% solids polymeric
colored
flake floor resurfacing system with superior wear, and chemical
resistance.
Product #315 with "multi-colored"
flakes
produces a durable, easy to maintain floor, on both new and old
surfaces.
|
|
|
Product #315BC Polymeric
Coating and Base Coat for the
315Chip
Flooring System. It can also be used as a stand alone coating.
If Epoxy.com Product #315BC is used as a stand alone coating over concrete, it is recommended that you first prime with
Product #889 Primer. |
|
|
Product #315BC - Fast Same as
Product #315BC
Polymeric Coating for Base
Coat for the 315Chip Flooring System
, but with a fast cure. |
|
|
Product #315BC-Cold Same as
Product #315BC
Polymeric Coating for Base
Coat for the 315Chip Flooring System
, but with a cold temperature cure. |
|
|
Epoxy.com #315NH is a 100%solids, moisture-insensitive
epoxy coating. Epoxy.com #315NH mixed at 2
:1 by volume ratio, produces an excellent coating for dry or damp
concrete, wood, or steel surfaces. Epoxy.com #315NH is available
in a summer grade and winter grade formulation. It can be
used as a stand alone coating or as a base coat for Epoxy.com
chip floor. It can also be used to replace
Product #315BC Polymeric
Coating when a non-hazmat to ship basecoat is required.
|
|
|
Product #316 Fast
Set Flooring -
a 100 % solids fast setting two-component epoxy
resin system. Is made to set fast even in
temperatures
below freezing. It is recommended for flooring, injection or anchor-bolt
grouting in the neat state or as a mortar when mixed #75 Filler
.
It exceeds most requirements of ASTM C-881-99,
Types I and IV , Grade 1, Class A. |
|
|
Product #340 Colored Chips forChip
Flooring |
|
|
Product #370 Replaced by
417 Elastomeric Waterproofing Horizontal Grade |
|
|
Product #371 Replaced by
417 Elastomeric Waterproofing
Vertical Grade |
|
|
Product #372 Black Waterproofing Membrane Knife
Grade |
|
|
Product #373 Replaced by
417 for Potable Water |
|
|
Product #374 Replaced by
419 Waterproofing Membrane |
|
|
Product #376
- Membrane below thin-set and tile |
|
|
Product #390
Flexible Acrylic
Roof Coating -designed to be a highly durable, flexible roof coating
with outstanding resistance to weathering, ultra-violet light and water.
Withstands ponding water conditions. It is suitable for application over
sprayed urethane foam insulation roofs, concrete, wood or asphalt roofs.
It serves as an excellent protection for urethane foam insulated storage
tanks, grain elevators, etc. |
|
|
PRODUCT #400
Chemical
Resistant Urethane is a two component, chemical resistant,
polyurethane coating. The high gloss finish offers excellent abrasion
resistance,
chemical and stain resistance, and superior color retention. It can
be used equally well on vertical or horizontal surfaces. It is ideal for
concrete floors. It is used as a finish coating option for most
EpoxySystems’
Flooring Systems. |
|
|
Product #401 Replace
by EpoxySystems' Product 458. |
|
|
Product #402 - Replace by
EpoxySystems'
Product #458 |
|
|
Product #403 Urethane Coating Aliphatic |
|
|
Product #404
Fast Cure Urethane Membrane |
|
|
Product #405
Fast Cure Urethane Topcoat. |
|
|
Product #407 Aliphatic Traffic Bearing Membrane
is a two component, ultra high solids aliphatic polyurethane elastomeric
membrane. When applied, it is resilient and accommodates movement in
concrete substrates. Epoxy.com Product #407 is used as a top coat
traffic bearing membrane or non-skid coating that retains color and
physical properties when exposed to harsh UV conditions. Epoxy.com
Product #407 is used as a system with Epoxy.com Product #882, and
may be applied as the top coat on Epoxy.com Product
#409 to maximize cost
effectiveness. Epoxy.com Product #407 cures at ambient
temperatures and is impermeable to moisture, oils, mild acids, gasoline,
and alkalies. |
|
|
Product #408 is
a black, liquid applied, single-component, moisture-cured 100% solids,
polyurethane waterproof coating, designed to form a low odor, seamless,
flexible rubber membrane impervious to moisture.
|
|
|
409 Traffic Bearing Membrane
is a Resilient Traffic Bearing Membrane
is a 100% solids, ambient cure impermeable elastomer. PRODUCT
#409
is resistant to moisture, oils, mild acids, gasoline, and alkalies.
PRODUCT
#409 when applied to concrete or other surfaces, is resilient
and accommodates
movement in concrete substrates. PRODUCT #409 is used
as a traffic
bearing membrane or non-skid coating that retains color and physical
properties
when exposed to harsh UV conditions. |
|
|
Product #410 replaced by
409 Traffic Bearing
Membrane |
|
|
Product # 415 Elastomeric
Membrane now called
Product #452 Polyurethane Membrane Standard |
|
|
Product #416
Polyurethane Coating a moisture-cured, liquid applied,
polyurethane,
based on Aliphatic Isocyanides in combination with additives and
pigments
to produce a wear resistant, protective and decorative floor coating,
for
interior and exterior applications. It is primarily used as the
protective
topcoat of the 450 and
450X2 deck coating systems, but when used with the proper primer,
can be used as a stand alone coating. |
|
|
Product #417
Elastomeric
Waterproofing A black, liquid applied
single-component moisture-cured
polyurethane coating, designed to form a seamless, flexible rubber
membrane
impervious to moisture. CompositioA black, liquid applied
single-component moisture-cured
polyurethane coating, designed to form a seamless, flexible rubber
membrane
impervious to moisture. Composition: Polyurethane elastomer. A
two-component
system is available, which does not depend on atmosphere moisture to
cure.
Type I: For horizontal surfaces. Type II: For vertical surfaces. USES:
allows
expansion and contraction over a broad temperature range and maintains
waterproofing
properties under continuous exposure to water. Type II has a thixotropic
consistency and may be used on vertical as well as horizontal surfaces.
417 remains flexible from -75°F to +175°F (-59°C to 79°C). Use as a
waterproof
membrane is intended for use wherever overflow water must be contained
. |
|
|
Product #417PW for Potable Water
is similar to #417 Elastomeric
Waterproofing
, but meets potable water standards |
|
|
Product #418 Elastomeric Membrane,
a black, self-leveling, liquid applied, two-component polyurethane
system,
designed to form a tough rubber membrane impervious to moisture. Type I:
For horizontal surfaces Type II: For vertical surfaces. Composition:
Polyurethane
elastomer. A two-component system, which does not depend on atmosphere
moisture
to cure. Basic Uses: Once cured, #418 allows expansion and contraction
over
a broad temperature range and maintains flexibility and waterproofing
properties
under continuous exposure to water above or below grade. PRODUCT #418
has
a thixotropic consistency and may be used on vertical as well as
horizontal
surfaces. PRODUCT #418 remains flexible from -75° to 175°F. |
|
|
Product #419 Waterproofing
Membrane Black Waterproofing Industrial
Strength is a black, liquid applied, two-component, high solids,
chemical
cured, polyurethane coating designed to form a tough rubber membrane
impervious
to moisture. Composition: Polyurethane elastomer. A two-component system
which does not depend on atmospheric moisture to cure. Basic Uses:
Once cured, #419 allows expansion and contraction over a broad
temperature
range and maintains flexibility and waterproofing properties under
continuous
exposure to water above or below grade. It has a thixotropic consistency
and may be used on vertical as well as horizontal surfaces. The #419
waterproof
membrane is intended for use on steel, wood, concrete, asphalt, tanks,
ponds,
roofs, foundations, etc. |
|
|
Product
#420 Urethane
Injection or moisture.EpoxySystems’ Product #420 reacts
with water and expands to form an impermeable HYDROPHOBIC barrier. When
reacted and hardened, EpoxySystems’ Product #420 is insoluble to water
and
other aggressive chemicals. |
|
|
Product #421 Urethane Injection resin |
|
|
Product #422
Replace
by Product #420 Urethane Injection resin flexible |
|
|
Product #423 Urethane Injection resin
|
|
|
PRODUCT #424 is a rigid two component
closed cell foam impervious to water and moisture. It can
be used
where structural foam is needed to encapsulate waste or restore the
physical
properties of timber and other masonry materials. |
|
|
Product #425
is a two component, HCFC-141b/water co-blown rigid polyurethane foam
system designed for low-density insulation applications. PRODUCT #425 is
typically used for floatation (Boat Foam) inside fiberglass parts. It
bonds
well to metals, wood and some plastics. This foam system meets Military
Specification P-21929B. |
|
|
Product #426 Urethane Gel |
|
|
Product #427 Urethane Cleaner |
|
|
Product #428 Urethane Safety Cleaner |
|
|
EpoxySystems’ Product #429
Urethane
Injection Resin Accelerator is specifically formulated to increase the
cure
rate of EpoxySystems’ Product #4
Urethane
Injection Resin. The accelerator liquid is normally used to
compensate
for cold weather or cold water temperatures. |
|
|
System #430 Elastomeric Multi-Colored
Decking System is a l iquid-applied, single-component,
moisture-cured, polyurethane deck covering system. For waterproofing
patios,
sundecks, stairways, balconies, etc. Product #430 can
be used on
all decks where a skid-resistant, long-lasting, wear-resistant,
water-proof
surface is required. It may be used on new decks as well as on old
concrete
decks which are damaged, or cracked. The system is suitable for exterior
as well as interior applications in all kinds of climates. The coating
retains
its elastomeric properties in below freezing weather as well as in very
hot climates. |
|
|
EpoxySystems’ PRODUCT
#431 is a two
component, flame retardant foam especially manufactured to provide a
rigid
foam with physical properties similar to that of timber or cement
grouts,
at a convenient one to one ratio, A to B, light black in color.
Product
#431 will bond to wet, moist or dry surfaces, even to
Plexiglas, with
no shrinkage and ample pot life after mixing A & B components. |
|
|
Epoxy.com Product #432 is a low
viscosity, rapid gelling, hydrophobic grout. Epoxy.com Product #432 is
used to seal leaks in cracked concrete, for soil stabilization and for
repairing leaking joints in structures. This all-purpose grout is easily
mixed with water or stabilizer at a convenient 1 to 1 by volume mix
ratio |
|
|
Product #440 Light Stable Deck Membrane |
|
|
EpoxySystems' Product # 441
is a two component water-based aliphatic (non-yellowing)
polyurethane. It is free of the health and
environmental problems
normally found in solvent-based urethanes, while maintaining excellent
performance
properties. Product # 441 polyurethane provides a
matte finish.
Product # 441 has good chemical, stain, and mar
resistance. In addition,
it’s easy to clean and has excellent color retention under heavy foot
traffic.
It is a high performance coating for use in a variety
of seamless
floor and wall coating systems. Product # 441
eliminates the strong
solvent odor normally associated with many high performance materials.
It’s
ideal for topcoats and finishes that require high abrasion resistance.
Typical
application areas are clean rooms, hospitals, pharmaceutical facilities,
stained concrete, wood floors, and as a seal coat for most Epoxy
Systems,
Inc. floor and wall coating systems. |
|
|
#450 Elastomeric
Flooring system provides a waterproof,
elastomeric, traffic bearing deck coating. It is a monolithic system
that
incorporates excellent adhesion, flexibility, impact, abrasion
resistance,
and chemical resistance. Petroleum products or cooling tower water
spillage
have little or no effect on the coating. Physical stresses imposed by
vibration
of equipment will not cause delamination or rupture of the coating. The
elastic properties of all system components enable the complete system
to
give and work with all but the most unusual movement of the floor or
deck. |
|
|
System
#450
Mechanical Room Flooring System - Liquid-applied,
single-component,
moisture-cured, polyurethane deck covering system. 450MR system provides
a waterproof, elastomeric, traffic bearing deck coating. It is a
monolithic
system that incorporates excellent adhesion, flexibility, impact,
abrasion
resistance, and chemical resistance. Physical stresses imposed by
vibration
of equipment will not cause delamination or rupture of the coating. The
elastic properties of all system components enable the complete system
to
give and work with all but the most unusual movement of the floor or
deck. |
|
|
System
#450X2
Urethane Decking Systemdouble strength is an
elastomeric
coating system for walking decks, balconies, patios, etc., where an
absolutely
waterproof coating is crucial, such as above living quarters and any
other
occupied areas |
|
|
System #450HT- High
Tensile Strength version of the 450 system for extra heavy duty
applications, like vehicular traffic. Epoxy.com Product #450HT is a
liquid-applied, single component, moisture-cured, seamless, slip
resistant, polyurethane, waterproof deck coating. |
|
|
Product #451
Aromatic
Polyurethane Coating -
is an aromatic, liquid applied, single-component,
moisture cured polyurethane floor coating for use in indoor applications
such as industrial plants, mechanical rooms, and locations where
surfaces
must withstand pedestrian traffic |
|
|
Product #452
Polyurethane
Membrane Standard is a
liquid applied, single component, moisture-cured polyurethane. It is the
major component of all EPOXYSYSTEMS’ PRODUCT #450 deck coating systems. |
|
|
Product #453 Elastomeric Mortar-
is a sloping system using an elastomeric binder adhesive
mixed with
aggregate for sloping decks, based on polyurethane elastomers. |
|
|
Product
#454
LVOC Polyurethane Membraneis
a liquid-applied, single
component, aromatic, moisture-cured polyurethane which will not blister
or gas. It may be substituted for our Epoxy.com Product #452.The
Epoxy.com 454 LVOC
Non-gassing Low VOC waterproofing membrane used with the all
Epoxy.com 430 and 450 Series systems. Epoxy.com 454 LVOC
Non-gassing
may be used to fill minor cracks in concrete, except for
expansion
joints where Epoxy.com Product #910 is
recommended. |
|
|
Product #455 Polyurethane Membrane Grading Material |
|
|
Product #456 Urethane Coating |
|
|
Product #457 Polyurethane Membrane 100% Solids |
|
|
Product #458
2Component Urethane Coatingis a liquid-applied,
two-component,
catalytic cured polyurethane floor and wall coating for use in air
fields,
industrial plants, stores, and other locations where surfaces must
withstand
heavy use of foot traffic. It provides a durable finish that protects
floors
against occasional chemical spillage, dirt, grease and oil. It gives
industrial
floors a well maintained look while retaining a glossy appearance.
Dusting
of concrete floors is eliminated when the surface is sealed with PRODUCT
#458 and, as dirt and oils are prevented from penetrating the concrete,
detergent and water easily clean the floor. PRODUCT #458 in pigmented
form may be used on floors to hide an unsightly appearance of the
substrate
or to provide a reflective, bright appearance that will lighten up a
warehouse,
highlighting work areas and traffic lanes. |
|
|
Product #460 Polyurethane Membrane and
Coatingis a two component, aliphatic, 100% solids, Zero
VOC, elastomeric,
traffic coating system for walking deck surfaces. Concrete or Plywood
substrates.
For waterproofing walking decks, balconies plazas, parking decks,
mechanical
room floors, etc. Designed for pedestrian and vehicular traffic. |
|
|
Product #462
High Tensile Strength Urethane Deck Membrane |
|
|
Product #466
High Tensile Strength Aliphatic Top Coating |
|
|
Product #469 Elastomeric Membrane Deck Grade |
|
|
System
#470 Multi Use Elastomeric System |
|
|
Product #471 Multi Use Base Coat |
|
|
Product #472 Multi Use HT |
|
|
Product #473 Aromatic Urethane Coating for #470
System |
|
|
Product #474 Aliphatic Urethane Coating for #470
System |
|
|
Product #475 Catalyst for #470 System |
|
|
System
#480 Elastomeric Deck |
|
|
Product #490 Athletic and Driveway
Surface
is a one part liquid applied coating with good ultraviolet
light
resistance. PRODUCT #490 is designed for use on pool decks, tennis
courts,
asphalt driveways, and concrete surfaces. This product is recommended
for
foot traffic areas to reduce slipping on commercial and industrial
floors.
Due to the waterbased formulation of the product, it can be installed in
areas where solvent based coatings are objectionable due to their odors
and fire hazards. This material can also be applied over damp as well as
dry surfaces |
|
|
Product #500 Polyester
Wood Filler Pine is a two component,
wood like polyester filler paste. Quick setting and easy to use.
EpoxySystems'
Polyester Wood Filler is designed primarily for wood repairs in
construction
surfaces. Can be used to fill areas of deteriorated concrete (or holes).
Also used by model shops for making permanent repairs, fillets, and
design
changes in the construction of all wood models and patterns.
EpoxySystems'
Polyester Wood Filler has excellent adhesion to wood, fiberglass, and
plaster
and can be worked with standard woodworking tools in a quick and
convenient
manner. |
|
|
Product
#501 Polyester
Wood Filler Mahogany is a two component, wood like
polyester
filler paste. Quick setting and easy to use. EpoxySystems' Polyester
Wood
Filler is designed primarily for wood repairs in construction surfaces.
Can be used to fill areas of deteriorated concrete (or holes). Also used
by model shops for making permanent repairs, fillets, and design changes
in the construction of all wood models and patterns. EpoxySystems'
Polyester
Wood Filler has excellent adhesion to wood, fiberglass, and plaster and
can be worked with standard woodworking tools in a quick and convenient
manner. |
|
|
Product #502 Polyester Wood Filler Hardener 1 oz. |
|
|
Product #503 Polyester Wood Filler Hardener 4 oz. |
|
|
Product #504
Polyester Paste
Gray is
a fast-setting industrial filler paste used for manufacturing,
fabrication
and repair in aircraft, aerospace and other industries having
requirements
for above normal temperature exposure. Fast and permanent applications
are
achieved by POLYPASTE. The service temperature of Filler 7 is up to 400
degrees F (205 degrees C). It is used in the construction industry to
seal
cracks for injection and for patches used on concrete, wood, steel and
other
suitable construction materials. Excellent machining and finishing
results
are accomplished by grinding, sanding, scraping, etc. When exposed to
elevated
temperatures, POLYPASTE has a tendency to darken but does not gas,
bubble,
or cause any finish distortion. This product does not contain wax and
readily
bonds to itself and other substrates such as FRP/SMC, hi-temp epoxy
molds,
aluminum, steel, cast iron, urethane foam parts, etc. POLYPASTE is
non-metallic,
non-conductive, and non-sparking. |
|
|
Product #505
Polyester Paste Black is
a fast-setting
industrial filler paste used for manufacturing, fabrication and repair
in
aircraft, aerospace and other industries having requirements for above
normal
temperature exposure. Fast and permanent applications are achieved by
POLYPASTE.
The service temperature of Filler 7 is up to 400 degrees F (205 degrees
C). It is used in the construction industry to seal cracks for injection
and for patches used on concrete, wood, steel and other suitable
construction
materials. Excellent machining and finishing results are accomplished by
grinding, sanding, scraping, etc. When exposed to elevated temperatures,
POLYPASTE has a tendency to darken but does not gas, bubble, or cause
any
finish distortion. This product does not contain wax and readily bonds
to
itself and other substrates such as FRP/SMC, hi-temp epoxy molds,
aluminum,
steel, cast iron, urethane foam parts, etc. POLYPASTE is non-metallic,
non-conductive,
and non-sparking. |
|
|
Product
#540 replace by Product #702 |
|
|
Product #541
Polyester Anchor Bolt Adhesive |
|
|
Product #550
Rapid Setting Trowel mortar |
|
|
Product #551
Thin Patch |
|
|
Product #600
Flexible Novolac is a two-component, 100% solids epoxy
coating based
on multi-functional high performance flexibilized resin. PRODUCT #600
provides
corrosion resistant protection to steel, other metals and concrete. It
has
excellent resistance to chemicals up to 300oF. It is resistant to
continuous immersion in water up to 212oF . PRODUCT #600 is formulated
in
a convenient 1 to 1 ratio, by volume mix ratio and has a long pot life
to
simplify application. PRODUCT #600 is more effective in applications
which
entail force curing. |
|
|
Product #630
Novolac Coating/Mortar Binder
-
a 100% solids epoxy Novolac ideal for harsh chemical and solvent
resistant
applications. It is ideal for use as a troweled mortar, slurry binder,
and
coating for concrete and steel in extremely corrosive areas where
resistance
to 98% sulfuric acid or other strong caustics is needed. It is ideal for use as a protective coating for
concrete and steel in the extremely corrosive areas of chemical plants
and
pulp mills secondary containment areas, water and waste treatment, and
gas
and electric utilities. |
|
|
Product #632 Novolac
Control Joint Filler is a
100% solids flexible Novolac epoxy Chemical Resistant joint filler for
saw-cut
joints of concrete slabs on grade. |
|
|
Product
#633 Novolac
Coatingis a 100% solids epoxy Novolac coating
ideal for
harsh chemical and solvent resistant applications.
Itis used in secondary
containment,
solvent storage, pump pads, trenches, and other high exposure areas.
Itis
ideal for use as a protective coating for concrete and steel in the
extremely
corrosive areas of chemical plants and pulp mills secondary containment
areas, water and waste treatment, and gas and electric utilities.
Product #633 is commonly used as a seal coat for
EpoxySystems' MORTAR SYSTEMS where chemical resistant
performance
is required. |
|
|
Product
#634 Novolac
High Temperature Epoxy - is
a 100% solids amine cured epoxy Novolac that is solvent free. Suitable
for
immersion and non-immersion service particularly in aggressive acid and
alkali environments with elevated temperatures. Epoxy Systems
Product #634 produces a tough, chemical resistant
coating on concrete, iron and non-iron surfaces. As a low viscosity
epoxy
Novolac it is suitable for hand or spray application. |
|
|
Product
#635 Novolac
Coating/Mortar Binder is a high solids epoxy
Novolac
coating ideal for severe chemical and solvent resistant applications.
It is filled with treated
ceramic
filler to provide improved chemical and thermal shock resistance. Itis
ideal for use as a protective coating for concrete and steel
in the extremely corrosive areas of chemical plants and pulp mills
secondary
containment areas, water and waste treatment, and gas and electric
utilities.
EpoxySystems' Product #635 is commonly used as a seal
coat
for EpoxySystems' MORTAR SYSTEMS where chemical
resistant
performance is required.
|
|
|
Product
#636 High
Temp Chemical Resistant Primer/Topcoat-
a 100%
solids amine cured epoxy Novolac that is solvent free. Specifically
designed
as a Methanol resistant coating. Product #635 is well suited for use in
a wide array of aggressive acids, alkalies and organic solvents. It
produces
a tough, chemical resistant coating on concrete, iron and non-iron
surfaces.
As a low viscosity epoxy Novolac it is suitable for hand or spray
application. |
|
|
Product #637
High Temp Coating/Primer is a
100% solids
amine cured epoxy Novolac that is solvent free. Suitable for immersion
and
non-immersion service particularly in aggressive acid environments.
Epoxy
Systems Product #637 produces a tough, chemical resistant
coating on
concrete, iron and non-iron surfaces. As a lower viscosity epoxy Novolac
it is suitable as a primer or as a top coating. Excellent against 98%
Sulfuric
Acid. |
|
|
Product #638
Glass Filled Novolac |
|
|
Product #640
Chemical & Heat Resistance is a two component; 100% solids
brush,
roll or airless spray applied coating designed to provide cavitation,
corrosion
and erosion resistance to concrete, metallic and nonmetallic surfaces.
PRODUCT
#640 acts as an inert barrier against extremely harsh environmental
factors
such as low and high PH, temperature extremes, dry and fluid particulate
flow and corrosive chemical attack. |
|
|
Product #641High
Temp Epoxy is a moisture-insensitive,
two-component, 100% solids epoxy coating. It is especially formulated to
protect concrete, steel and wood subject to high temperatures and
corrosion. |
|
|
Product #641LV High Temp Resistant
Mortar
is a two component highly cross-linked novolac epoxy resin
system.
It is especially formulated to be used as a high temperature grouting or
laminating resin. It is used to protect concrete, steel and other
substrates
from high temperatures and corrosion. |
|
|
Product #642
Multifunctional High Chemical Resistance Epoxy
Coating/Bonder
is a two component, 100% solids, one coat trowel grade
or grout pump applied protective coating designed to provide cavitation,
erosion and corrosion resistance to metallic and non-metallic surfaces.
Product #642 acts as a barrier against extremely harsh environmental
factors
such as low and high PH, temperatures extremes, dry and fluid
particulate
flow and corrosive chemical attack. |
|
|
PRODUCT #643
Highly Chemical Resistant Coating is a solvent free, high functionality
Novolac epoxy coating suitable for immersion and non-immersion service.
Designed specifically as a Methanol resistant coating. It is well
suited for protection in a wide array of aggressive acids, alkalies and
organic solvents. It produces a tough, chemical resistant coating on
ferrous
and non-ferrous metals and concrete. |
|
|
Product #644 High Temp Chemical
Resistant Coating. Similar to 641LV, but with
fillers
to make it thicker. |
|
|
648 Chemical Resistant Coating
is
a two component high performance epoxy resin formulated with a
convenient
1 to 1 mix ratio. EPOXYSYSTEMS’ PRODUCT #648 Chemical Resistant Coating
has been developed as a coating for exposure to organic acids and other
severe chemical environments. It is used widely in the food and chemical
industries for protection of concrete, wood, and steel. EPOXYSYSTEMS’
PRODUCT
#648 is suitable for application by brush, roller or spray. Where
in-shop
production techniques may be utilized and elevated temperature curing is
feasible, rapid property development may be achieved by curing at 200 -
250°F (93 - 121°C). This will provide a cured film which may be handled
within a relatively short period of time (about 4 hours). Elevated
temperature
curing will also enhance ultimate physical and chemical resistant
properties. |
|
|
Product
#650 Resurfacing
Grade Epoxy Ceramic Filled Epoxy Coating |
|
|
Product #651 Ceramic Filled Epoxy Mortar is a
two-component, 100% solids, ceramic reinforced, trowelable polymeric
compound which can be used to repair virtually any metal surface that has
been damaged by erosion/corrosion, cavitation or abrasion. |
|
|
Product
#652 Metal
Filled Trowel Grade Epoxy - a two-component, 100%
solids,
metal-reinforced polymeric compound which can be used to repair
virtually
any metal surface that has been damaged, cracked or worn. |
|
|
Product #653 Emergency Epoxy Liquid Grade |
|
|
Product #654
Metal Filled Internally lubricated Trowel Grade |
|
|
Product #669
Strait Vinyl Ester Resin |
|
|
Product #670
Vinyl Ester General Purpose
is formulated from a vinyl ester, low
viscosity resin of 100% reactive solids in a composite with inorganic
fiber
reinforcement. It provides the ultimate in chemically resistant
properties
to prevent deterioration where reactive chemicals exist |
|
|
Product #671 Conductive Primer/Sealer
-
EpoxySystems’ Product #671 is a low viscosity, two component,
carbon filled, polyamide modified conductive primer/sealer formulated
with
special wetting agents to provide maximum penetration into concrete
surfaces.
Product #671 is ideal for both new and old concrete surfaces. Product
#671
provides excellent resistance to wear, and can be used either alone or
as
a conductive sealer or as a conductive primer when used with
EpoxySystems’
product #674 Electro-Static Dissipating Urethane Topcoat and
EpoxySystems’
Conductive Systems. |
|
|
Product #672 Conductive Epoxy
is a two component, 100% solids epoxy/aggregate material
that utilizes the latest in conductive floor technology. Epoxy Systems'
CONDUCTIVE EPOXY can be installed as a coating or as a component to
Epoxy
Systems’ Flooring Systems. It can also include Epoxy Systems
ELASTOMERIC MEMBRANES to produce
waterproof, crack resistant Systems. Typical Uses of include:
Ammunitions
Facilities, Paint and Solvent Storage Areas,Electronic Component Plants
Hazardous Materials Storage Areas |
|
|
Product #673 Conductive Terrazzo |
|
|
PRODUCT #674 -
Electrostatic Dissipative Urethane Coating
is a two component, Electro Static Dissipative chemical resistant,
polyurethane
coating. The high gloss finish offers excellent abrasion resistance,
chemical
and stain resistance, and superior color retention. EPOXYSYSTEMS’
PRODUCT
#674 can be used equally well on vertical or horizontal surfaces. It is
ideal for concrete floors and walls in warehouses, storage facilities,
aircraft
hangars, animal housing, and vehicle maintenance facilities. Available
in
both clear and pigmented formulations, EPOXYSYSTEMS’ PRODUCT #674 is
used
as a finish coating option for most EpoxySystems’ Flooring Systems. |
|
|
Product #675 Electrostatic Dissipating
Water Borne Epoxy Topcoat-a pigmented, water emulsion
epoxy electro-static
dissipative finish designed to have maximum penetration into concrete
surfaces
to provide high bond strength and adhesion. It has very low odor and can
be used in occupied areas as a finish sealer in Thin-Film Electro-Static
Dissipative Coating Systems. |
|
|
Product #680 MMA
Polymer
Concret |