Epoxy Gel Adhesive and Bonding
Vertical and Overhead Epoxy Adhesive Resin
Epoxy Patching Gel
Epoxy.com Product #2006
DESCRIPTION
Epoxy High-Mod Gel Adhesive and Bonding Resin - Product #2006 is a 100% solids high-mod epoxy
gel adhesive used for vertical and overhead bonding applications and structural
repairs. Epoxy High-Mod Gel Adhesive and Bonding Resin - Product #2006 is also used as a grout for anchor bolts, dowels and rebar. Epoxy High-Mod Gel Adhesive and Bonding Resin - Product #2006
Meets ASTM C881 Requirements for Type I, Type II, Grade 3, Class B, C, D, E.
ADVANTAGES
- Non-sagging Epoxy Gel Formulation
- Exceeds requirements for A.S.T.M. C-881 Types I, II, Grade 3, Class "B","C",
"D", and "E"
- 100% Solids Zero (0) VOC - having no VOC it meets the strictest Low VOC
requirements
- Proven field performance
- Slower setting - more time to do the job right
- Waterproof Epoxy Gel
Uses
- Bonding Hardened Concrete to Hardened Concrete
- Bonding Wood to Wood
- Bonding Wood to Concrete
- Dowel Bar Adhesive
- Anchor Bolt Adhesive
- Patching Concrete - Horizontal, Vertical and Overhead
- Patching Wood - Horizontal, Vertical and Overhead
- Setting Injection Ports - for concrete and wood injection
- Waterproofing
APPLICATION PROCEDURES
Surface Preparation
Before application of gel, surface to be bonded must be clean and sound.
Remove all dirt, laitance, grease, curing compounds and other foreign
matter by sandblasting, or mechanical abrasion. When performing repairs,
remove all unsound concrete before repairing. See
Epoxy Surface Preparation Procedures for more information.
Remove water and dust
from all surfaces with an oil-free air blast immediately prior to
application. Although damp surfaces will not deter the bond, all free and standing water
must be removed before application begins.
Mixing Instructions
Temperature of Epoxy High-Mod Gel Adhesive and Bonding Resin - Product #2006 must be 50° F. or above at
time of mixing. Stir each component separately, before blending. Mix 2 Parts A and
1Part B for three minutes with a low speed
electrical drill equipped with a jiffy mixer or paddle. To prepare a mortar add
one part by volume of clean, dry, well graded select sand to one part by volume
of mixed epoxy.
Application
To apply Epoxy.com Product #6 use a spatula, trowel or caulking gun.
Limitations
Use of solvents for thinning Epoxy.com Product #2006 will prevent
proper cure. Temperature of substrate must be above 50°F. Age of
new concrete must be a minimum of 28 days. Maximum
thickness per lift for patching application is 1/2".
SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye or skin
irritation. If contact occurs, wash immediately and seek
medical help.
Use safety glasses with side shields and wear protective
rubber or polyethylene gloves.
CLEANING
All tools and equipment should be cleaned before the system gels.Use toluene,
Methyl ethyl ketone or any lacquer solvent.
SPECIFICATIONS
| Mix Ratio |
2:1 by Volume |
| Mix Viscosity |
Gel |
| Bond Strength PSI Min. |
1,500 |
| Gel Time (150 g mass @ 70° F |
30-40 min. |
| Flash Point in °F |
>200 |
| Consistency |
No Sag Gel |
| Initial Cure |
24 hr. (80% ultimate strength) |
| Final Cure |
7 Days |
| Lineal Coefficent of Shrinkage |
.005 (max) |
| Compressive Modulus (psi) |
150,000 (min) |
| Compressivie Yield (psi) at 7 day cure |
5,000 (min) |
| Tensile Strength @ 75 degrees F at 7 days |
4000 P.S.I (34.5 MPa) |
| Flexural Strength (psi) |
11,000 (min) |
| Heat Deflection Temperature °F |
120 (min) |
| Elongation at break (%) |
1.0 (min) |
| Peak Exotherm °F |
178 |
| v.o.c (mixed) |
0.0 |
| Coverage @ 30 mils |
53 sq. ft./gal |
| Packaging |
1.5 gal units, 3 gal units, 15 gal units |
| Shelf Life |
2 years |
Physical properties are typical values and not specifications. Please see reverse
side for limitations of our liability and warranty
Coverage
There are 231 cubic inches to a gallon. So you will get about 25.6 square
feet per 1/16 inch of thickness. If using this as an anchor bolt, or dowel bar
adhesive, you can double check you volume with the
Epoxy.com Dowel Bar and Anchor Bolt Adhesive Calculator.
CHEMICAL RESISTANCE
Epoxy High-Mod Gel Adhesive and Bonding Resin - Product #2006 is excellent against distilled water, most inorganic
acids and alkalies and moderate against alcohols or aromatic solvents.
BONDING IRREGULAR SURFACES
Use the gel to bond two irregular surfaces together.
VERTICAL AND OVERHEAD REPAIRS
For small cracks and shallow repairs, use the gel; for larger repairs use
conjunction with silica. Trowel mixture into repair area.
BLOG POSTS & NEWS
You can find more information on
Epoxy Gel Products, and many of our other products at
news.epoxy.com.
NOTICE TO BUYER
DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
Products are manufactured to strict quality assurance specifications and that
the information supplied by us is accurate to the best of our knowledge. Such
information supplied about our products is not a representation or a warranty.
It is supplied on the condition that you shall make your own tests to determine
the suitability of our product for your particular purpose. Any use or
application other than recommenced herein is the sole responsibility of the
user. Listed physical properties are typical and should not be construed as
specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER
INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM
ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE
MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO
WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT
INFRINGE UPON ANY PATENT. We shall have no liability for incidental or
consequential damages, direct or indirect. Our liability is limited to the net
selling price of our product or the replacement of our product, at our option.
Acceptance of delivery of our product means that you have accepted the terms of
this warranty whether or not purchase orders or other documents state terms that
vary from this warranty. No representative is authorized to make any
representation or warranty or assume any other liability on our behalf with any
sale of our products. Our products contain chemicals that may CAUSE SERIOUS
PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW
ALL PRECAUTIONS TO PREVENT BODILY HARM.
|
|
Proper mixing and installation is critical to the optimal success of all products.
See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA
We have products that have passed the test of time as well as the best new Systems available today.
Since 1980 - 40 years of the highest quality products
Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)
Closed for lunch from 12Noon to 1PM
321-206-1833 Customer Service - Ordering and Order Status
Katey Lambert-Fontaine, VP - Chief Operations Officer
sales@epoxy.com
Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
Copyright © 1994-2025 (providing
online information about the right product for the right job for nearly 30 years) EPOXY.COM a
division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
|
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.
|
|