|
.
Epoxy.com Product #652Metal Filled Trowel Grade EpoxySteel Bonding - Steel Resurfacing - Steel RepairDESCRIPTIONEpoxy.com PRODUCT #652 Metal Filled Trowel Grade Epoxy is a two-component, 100% solids, metal-reinforced (316 stainless steel) polymeric compound for Steel Bonding, Steel Resurfacing and Steel Repair. PRODUCT #652 Metal Filled Trowel Grade Epoxy gel adhesive can be used to repair virtually any metal surface that has been damaged, cracked or worn. Also used as an adhesive to bond steel to steel and steel to concrete, wood to steel, etc. Contact Epoxy.com technical support department for details on the proper use of this material for bonding applications. ADVANTAGES
WHERE TO USE
SURFACE PREPARATIONAll surfaces to be repaired with PRODUCT #652 Metal Filled Trowel Grade Epoxy must be clean of dirt, grease and oil. For best results, remove contamination with abrasive blasting and non-flammable cleaner/degreaser, making sure all dust is removed. See www.epoxy.com/surfaceprep.aspx for more details. MIXINGEither mix the entire contents of the base and activator or measure three (3) parts of base and one (1) part of activator, by volume, and mix with spatula thoroughly to produce a streak-free material. Scrape mixing board frequently to insure complete mixing. APPLICATIONApply PRODUCT #652 Metal Filled Trowel Grade Epoxy Gel Adhesive by stiff brush or applicator. Material should be worked into the profile of the surface to achieve maximum adhesion. Material can be heat-cured for one (1) hour at 200°F to achieve ultimate properties.
CURE CYCLEImmersion/Full Chemical and/or heat Exposure 5 days Force cures must be used for enhancement of high temperature and chemical resistant properties or to allow the coating to be placed in service before 5 days. Allow the coating a post cure of 12 to 24 hours before force curing. RECOMMENDED FORCE CURE SCHEDULE LIMITATIONSPRODUCT #652 Metal Filled Trowel Grade Epoxy gel adhesive should be used in 40° to 90° F temperatures and in less than 90% humidity. SHELF LIFEOne (1) year in closed containers. Store between 60° F and 85° F. CAUTIONS"A" Component: Warning! Contains epoxy resin. May cause skin irritation or allergic response. Avoid contact with skin. Avoid breathing vapors when heated. Wear protective gloves, goggles and barrier creams. In case of skin contact, wash thoroughly with soap and water. In case of ingestion, do not induce vomiting. "B" Component: Warning! Danger! Causes severe burns. Contains alkaline aimes-strong sensitizer. Avoid skin contact. Avoid breathing vapors when heated. Wear protective gloves, goggles and barrier creams. In case of skin contact, wash thoroughly with soap and water. In case of ingestion, induce vomiting. If irritation persists, seek medical attention. FOR INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2011 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products] [Where to Start] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Epoxy.com Coatings] [Conductive Electrostatic Dissipative] [Applications] [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Epoxy and Urethane Injection of Concrete] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Product Guide] [Wood Filler] [Who We Are] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format] [Epoxy.com Online Ordering Authorization Form]
|
