Epoxy Injection Resin
For Concrete and Wood
Waterproofing Structural Repair
Product Description
Epoxy.com Product #3301 is a 2-component, low viscosity, 100% solids,
epoxy injection resin for concrete and wooden substrates.
DESCRIPTION
Epoxy.com Product #3301 is a 100% solids low viscosity epoxy adhesive used to restore cracked structural
concrete by the pressure injection method and to grout cracks in a horizontal plane by gravity.
ADVANTAGES
- Low viscosity � exceptional flow characteristics
- High Strength
APPLICATION PROCEDURES
Surface Preparation for Epoxy Injection
Surface must be clean and sound. Interfaces of cracks must be free of dirt, laitance, grease, curing compounds and other foreign matter. Flushing with water
through ports under pressure may he necessary prior to epoxy injection. Cracks may be damp or wet.
Epoxy Mixing Directions
Temperature of Product #3301 must be 60°F. or above at time of mixing.
Stir each component separately before blending. Best if used in an automatic binary mixing system.
If mixed manually mix two parts by volume of Part A with one part by volume of B for three minutes with a
low-speed electric drill motor equipped with a mixing paddle.
Application Epoxy Injection Resin
For pressure injection set ports at intervals that approximately equal the thickness of the member
to be injected in inches. Ports may need to place closer together for very fine cracks, or may
be slightly further for wider cracks. Seal between and around each port with Product #2005,
or #2006. Inject Product #3301 from an epoxy injection machine or binary hand or pneumatic injection gun.
For more information consult Epoxy.com� technical service department.
Limitations of Epoxy Injection Resin
Minimum substrate temperature must be 50° F.
Cleaning Epoxy Injection Resin from Tools
All tools and equipment should be cleaned before the system gels.
Use methyl ethyl ketone or any lacquer solvent.
Environment & Health
This is a solvent free and Nonyl Phenol free product, and practically odorless during application.
Follow the appropriate Occupational Health and Safety guidelines applicable to the location where
the application is undertaken. For more information, please refer to the safety datasheets for the
individual components.
Ratio of Components
2 parts of component A are mixed with 1 part of component B, by volume.
Add Hardener B to Base A. Mix with slow speed drill and appropriate mixing paddle taking care not
to entrain air. May also be mixed by appropriate static mix tube.
Application Temperature
The recommended substrate temperature is 60° - 80°F, but no less than 50°F.
Application Time/Pot Life
Mixed product should be used within 40 minutes at a temperature of 70°F. At higher temperatures the
application time is shorter.
Curing Time (at 70°F)
Approximately 12 hours. The product is fully hardened after 5 - 7 days.
Colors
Transparent
Finish
Gloss
Solids Content
Approx. 100 %
VOC
12 g/l
Density
Component A approx.- 9.30 lbs/gal (1.12 kg/l)
Component B approx. - 8.60 lbs/gal (1.03 kg/l)
Mixed approx. - 9.10 lbs/gal (1.09 kg/l)
Storage
12 months in unopened pack. Storage temperature between 40°F and 100°F.
Protect from weather and moisture / contaminant ingress (tightly sealed to prevent air
infiltration, and exfiltration).
Packaging
The product is delivered A+B in the following packs:
| Unit | Base A | Hardener B |
| 3 gallons | 2 Gallons | 1 Gallon | |
| 12 Gallon | 2 each 4-Gallons | 1 each 4 gallon |
Physical Properties
| Property |
Result |
Test Method |
| Compressive Strength |
>11,600 psi |
ASTM C579 |
| Flexural Strength |
> 8,700 psi |
ASTM C580 |
| Compressive Strength |
>11,600 psi |
ASTM C579 |
| Tensile Strength |
>7,175 psi |
ASTM C307 |
Further Information
If you would like additional information, please Epoxy.com Technical Support Department
Disclaimer
Any recommendation or suggestion relating to the use of the products sold by Epoxy,com whether in its technical literature, or in response to a specific enquiry, or otherwise, is based upon data believed to be reliable, however the products and information are intended for use by Customers having requisite skill and know-how in the industry and therefore it is for the Customer to satisfy itself of the suitability of the products for its own particular use and it shall be deemed that the Customer has done so at its sole discretion and risk.
|