[Epoxy Home] [Catalog of Products] [Where to Start] [Guide Specs] [Epoxy Installation Guides] [Blog Posts] [Epoxy Bonding Systems] [Chip Floors] [Chemical Resistant Epoxy] [Seamless Coatings] [Conductive Epoxy Flooring] [Crack Injection of Concrete & Wood] [Applications] [Elastomeric Polyurethane Systems]  [Seamless Garage Flooring Resins] [High Temperature Epoxy Resins] [Seamless Industrial Floors] [Joint Systems & Sealants] [Methyl Methacrylate MMA ] [Novolac Epoxy Resins] [Epoxy Mortars & Grouts] [Epoxy Novolac] [Primers Sealers] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Epoxy Installation Tips] [Who We Are]  [Epoxy Tech Data Sheets in Acrobat] [Product MSDS Sheets] [Online Order Authorization Form][Contact UsPhone 352.489.1666

  Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980Contact Us  

Epoxy.com Product #417

Elastomeric Membrane Waterproofing System Coaltar-Free

This Product has been Replace by Epoxy.com Product #449


This Material requires a minimum product purchase. Please see our Products That Require a Minimum Order Page, or contact Epoxy.com for more information.


DESCRIPTION:

A black, liquid applied single-component moisture-cured polyurethane coating, designed to form a seamless, flexible rubber membrane impervious to moisture. Composition: Polyurethane elastomer. Type I: For horizontal surfaces. Type I: For vertical surfaces.

Type II: For vertical surfaces.

 

BASIC USES:

Once cured, EPOXYSYSTEMS’ PRODUCT #417 allows expansion and contraction over a broad temperature range and maintains waterproofing properties under continuous exposure to water. EPOXYSYSTEMS’ PRODUCT #417 Type II has a thixotropic consistency and may be used on vertical as well as horizontal surfaces. EPOXYSYSTEMS’ PRODUCT #417. remains flexible from -75°F to +175°F (-59°C to 79°C). EPOXYSYSTEMS’ PRODUCT #417 waterproof membrane is intended for use wherever overflow water must be contained.

 

Suggested areas of application are as follows:

  • Waterproofing in between concrete slabs, such as parking decks, roof decks or courtyard areas over subterranean parking.

  • Waterproofing below grade exterior walls or foundations and basements or other structures that are to be backfilled.

  • Waterproofing inside planter boxes.

  • Waterproofing under terrazzo or tile floors.

  • Waterproofing under shower-pans, kitchen, laundry and bathroom floors.

  • Waterproofing inside of elevated swimming pools.

  • Waterproofing of occupied areas under malls, plazas and promenades.

  • Water Tanks: EPOXYSYSTEMS’ PRODUCT #417 has been used with outstanding success as a lining for emergency water storage tanks. The EPOXYSYSTEMS’ PRODUCT #417 bridges hairline cracks and because of the materials flexibility, allows them to move with changes in temperature. The product is fully bonded to the substrate so water cannot flow underneath the lining as it can with sheet lining materials.

 

Advantages:

  • EPOXYSYSTEMS’ PRODUCT #417 is a single-component compound that may be used directly from the container with no mixing required.

  • The addition of catalysts are not necessary, as EPOXYSYSTEMS’ PRODUCT #417 is a moisture-cured compound.

  • May be applied by spray equipment, brush, roller, squeegee or trowel, without the need for heating the material.

  • May be applied over concrete, stone, brick, cement blocks, wood, metal, asbestos and most other surfaces.

  • EPOXYSYSTEMS’ PRODUCT #417 cuts cost of application by eliminating mixing, splicing, sealing tapes, adhesives and other labor consuming methods required when installing other conventional types of waterproofing systems.

  • The superior flexibility and elongation properties of EPOXYSYSTEMS’ PRODUCT #417 allows expansion and contraction with the substrate, without cracking or becoming brittle.

  • Does not contain any potentially hazardous coal tar.


APPLICATION:

  • EPOXYSYSTEMS’ PRODUCT #417 is best applied by airless spray. However, when the job does not lend itself to spraying, it may also be applied by roller, brush or squeegee.

  • All cracks over 1/16" (1.6mm) in width must be filled and covered with EPOXYSYSTEMS’ PRODUCT #417 Non-sag. This product may be applied by trowel or caulking gun. There is no need to wait for this product to cure before applying the EPOXYSYSTEMS’ PRODUCT #417 since they are completely compatible.

  • A dry film thickness of 60 mils (1.5mm) is recommended over concrete surfaces. Extremely porous substrates should be filled prior to coating or receive additional EPOXYSYSTEMS’ PRODUCT #417

  • EPOXYSYSTEMS’ PRODUCT #417 may be used in a single 60 mil (1.5mm) application over sound surfaces without danger of gassing. Application must be made uniformly to avoid thin spots and care must be taken to avoid pinholes and repair them should they occur. Coverage to obtain 60 dry mils is 20 sq. ft./gallon (0.48 m2/Liter). Where a two coats application is preferred, two coats at 40 sq. ft./gallon (0.96 m2/liter) per coat are to be applied, allowing a 24 hour cure time between coats.

  • Protection board must be used prior to backfilling or pouring the concrete topping slab.

 

Shelf Life: 6 months at 77°F (25°C) when stored indoors in cool and dry location.

Color: Black only.

Standards: A.S.T.M. C836-89.

LIMITATIONS:
Containers that have been opened must be used within one or two days since it is a moisture-reactive material. It sets up when exposed to air. All surfaces must be completely free of foreign matter and dry before recoating it with EPOXYSYSTEMS’ PRODUCT #417..

PHYSICAL PROPERTIES

Property

Test Method

Type-I

Type-2

Viscosity (poise)

Brookfield Viscometer

35± 5

250± 20

Weight /Gallon Pounds

10.00± 0.2

9.12± 0.2

Weight / Gallon Kilograms

4.50± 0.1

4.10± 0.1

Percent Solids

Weight

Volume

ASTM D-2369

85.00%

78.00%

82.00%

77.00%

Tackfree Time

at 77°F (25°C) and 55% R.H.

12-16 hrs

12-16 hrs

Recoat Time

at 77°F (25°C) and 55% R.H.

16-24 hrs

16-24 hrs

Hardness (shore A)

ASTM D2280

15A

30A

Tensile Strength (p.s.i)
(N/sq. m)

ASTM D412

300
2.1

436
3.0

Percent Elongation

ASTM D-412

1000%

700%

Water Vapor Transmission
(grains/hr/ sq. ft.)

ASTM E-96
(procedure B) water method

2.08

1.412

Adhesion to Concrete

ASTM D-903

8 lb/in no peel/film break (1.5kg/cm)

9 lb/in no peel/film break(1.6 kg/cm)

Hydrostatic Pressure Resistance

ASTM D-751

94 p.s.i (0.65 N/sq. m)

Resistance to Decay

ASTM D-154

no surface defects

no surface defects

Moisture Vapor Transmission

(grains/hr/sq. ft - after decay test)

N.av.

1.563

Flash Point

120°F (49°C)

150°F (66°C)

Recovery (percent)

ASTM D-412

98%

96%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRODUCT WARRANTY:

All products proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control we cannot accept damage in excess of the purchase price of these products.

MAINTENANCE:

If EPOXYSYSTEMS’ PRODUCT #417 is damaged, it can be repaired by cleaning the 

Hit Counter

Exclaim

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information on Epoxy.com Products please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

 352-533-2167  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Website:  www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright 1994-2014 (providing online information about the right product for the right job for 20 years) EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy.com a division of Epoxy Systems, Inc.  (hereinafter known as "Supplier" warrants its products (when properly stored) for the period of time as follows: Epoxy one (1) year; Polyesters, Methyl Methacrylate  and Polyurethanes Six (6) months.  Supplier warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Supplier. If any product fails to meet this warranty, the liability of Supplier will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Supplier within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Supplier may in its discretion refund the price received by Supplier in lieu of replacing the material. No customer, distributor, or representative of Supplier is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Supplier. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Supplier reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. SUPPLIER'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND SUPPLIER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by us in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

 

[Home] [Catalog of Products [MSDS in Acrobat Format]  [Online Ordering Authorization Form] [Add Epoxy.com to Favorites]

Hit Counter