|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home
|
|
EpoxySystems' Product #419 INDUSTRIAL STRENGTH ELASTOMERIC MEMBRANE Replace by Epoxy.com Product #449
PRODUCT DESCRIPTION Composition: Polyurethane elastomer. A two-component system which does not depend on atmospheric moisture to cure.Basic Uses: Once cured, EPOXYSYSTEMS’ PRODUCT #419 allows expansion and contraction over a broad temperature range and maintains flexibility and waterproofing properties under continuous exposure to water above or below grade. EPOXYSYSTEMS’ PRODUCT #419 has a thixotropic consistency and may be used on vertical as well as horizontal surfaces. EPOXYSYSTEMS’ PRODUCT #419 waterproof membrane is intended for use on steel, wood, concrete, asphalt, tanks, ponds, roofs, foundations, etc.
Water Tanks: EPOXYSYSTEMS’ PRODUCT #419 has been used with outstanding success as a lining for potable water storage tanks. The EPOXYSYSTEMS’ PRODUCT #419 fills and covers the crack and because of its flexibility, allows them to move with changes in temperature. The product is firmly bonded to the substrate so water cannot flow underneath the lining as it does with sheet lining materials. Also used as a joint filler for applications in water storage and sewage treatment environments.
Advantages: Applied by airless spray methods, brush, roller, squeegee or trowel. EPOXYSYSTEMS’ PRODUCT #419 cuts cost of application by eliminating splicing, sealing tapes, adhesives and other labor consuming methods required when installing other conventional types of waterproofing systems. The superior flexibility and elongation properties of EPOXYSYSTEMS’ PRODUCT #419 allows expansion and contraction with the substrate without cracking or becoming brittle. EPOXYSYSTEMS’ PRODUCT #419 has excellent abrasion resistance for applications where there may be contact with floating debris. May be applied over a variety of substrates including concrete, stone, brick, cement blocks, wood and metal. Environmentally safe, complying with VOC standards.
Shelf life: 1 year in unopened containers. PRODUCT WARRANTY All products proven to be defective in manufacture will be replaced at no charge. Since the use of these products is beyond our control, we cannot assume any risk or liability for results obtained, nor can we accept damages in excess of the purchase price of these products. SAFETY DATA The EPOXYSYSTEMS’ PRODUCT #419 contains petroleum hydrocarbon, petroleum naptha, and other ingredients. Health and safety precautions should be observed during the storage and use of this product. Avoid contact with moisture or water. Please refer to the Material Safety Data Sheet for further information. MAINTENANCE If EPOXYSYSTEMS’ PRODUCT #419 is damaged, it can be repaired by cleaning the surface and recoating it with EPOXYSYSTEMS’ PRODUCT #419.
Priming: EpoxySystems’ Product #888 Primer is used to prime green concrete (more than seven day cure for normal structural concrete). It is also used to prime damp concrete, masonry, or wood surfaces on which the waterproofing membranes are to be applied, as well as on adequate cured and dry surfaces.Although EPOXYSYSTEMS’ PRODUCT #888 PRIMER may be used on green concrete and damp surfaces, moisture may become trapped under the waterproofing membrane. This may result in blistering, particularly on warm, sunny days. Therefore, cover the membrane as soon as possible to minimize blistering. Blistering over 4" in diameter should be cut and patched with membrane. Concrete: Utilizing EPOXYSYSTEMS’ PRODUCT #888 PRIMER will allow the application of the EPOXYSYSTEMS’ PRODUCT #419 to be made on green concrete. Concrete must be free of any curing compounds or bond release agents. Existing concrete should be free from foreign matter, oil, greases, etc. Concrete sections shall require the removal of fins, ridges and other protrusions and patching of voids. Remove oil and grease with a commercial grade alkaline cleaner; thoroughly rinse and dry. Wood: All plywood to receive coating shall meet or exceed requirements for A-C plugged, exterior grade. Metal: Metal surfaces shall be dry, clean, free of grease, oil, dirt, rust and corrosion. Other coatings and contaminants could effect bond of coating system. Existing Coatings: In the case of an existing coating, it should be determined whether or not there will be compatibility and adhesion between the EPOXYSYSTEMS’ PRODUCT #419 and the existing coating system. This can be determined by applying a sample test patch to verify procedures for a successful application of the new coating system. If adhesion is proven to be poor, then removal of the existing coating is necessary. Job Conditions: Install coating materials under conditions where all of the following conditions are met.
Application : EPOXYSYSTEMS’ PRODUCT #888 PRIMER may be applied to clean, dirt free, frost free, surfaces at a coverage rate of 250-350 sq. ft. per gallon. Do not apply to frozen concrete or to concrete with standing or visible water. Do not use during precipitous weather. Do not apply on wet surfaces or when rain is imminent, or when the surface may become wet prior to a full cure. Keep container tightly closed. Avoid contamination with water, make sure all application equipment is completely dry. For use in constant submersion, the recommended thickness must be achieved in one day with as many coats as needed. On vertical surfaces at least two coats will be required to achieve a minimum of 60 dry mils. Recoating must be done before first coat firms, but it must be done within 24 hours. If EPOXYSYSTEMS’ PRODUCT #419 has cured more than 24 hours, the surface must be roughened up and primed before reapplying. EPOXYSYSTEMS’ PRODUCT #419 may be used in a single 60 mil application over sound surfaces without danger of gassing. Application must be made uniformly to avoid thin spots and care must be taken to avoid pinholes and repair them should they occur. Coverage to obtain 60 dry mils is 24 sq. ft./gallon. Protection board must be used prior to backfilling or pouring concrete.
|
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Technical
Data Sheets in Adobe Acrobat Format][MSDSs
in Adobe Acrobat Format][Online-
Ordering Authorization Form]
|
