|
Epoxy.com Product #670 Vinyl Ester Coating/Mortar Epoxy.com PRODUCT #670 Field Formed System is formulated from a vinyl ester, low viscosity resin of 100% reactive solids in a composite with inorganic fiber reinforcement. It provides the ultimate in chemically resistant properties to prevent deterioration where reactive chemicals exist.ADVANTAGES PRODUCT #670 may be used even at 32oF (0oC) and still permits the efficient wetting out of fiber reinforcement. Set time can be controlled regardless of temperature by increasing or decreasing catalyst (Component "B"). The resin-cloth combination produces excellent impact resistant properties. A ten-year track record has proven that even under severe chemical exposure, it prevents deterioration in pickling tank operations where a 50% solution of hydrochloric acid is used.
USES Steel, concrete, aluminum and timber tanks. Industrial flooring where high chemical resistance is required.
SURFACE PREPARATION The surfaces to receive the PRODUCT #670 Field Formed System if concrete is new shall be a minimum of 3 days old when used with Product #105 Catalytic Agent in the concrete, for plain concrete, 7 to 14 days. Surfaces should be dry. The surfaces shall be lightly abrasive blasted, power wire brushed. If applied to steel, the steel should be abrasive blasted, brushed or other suitable preparation in accordance with SSPC-SA10. All grease, oil, dirt, or other deleterious substances shall be removed.
PACKAGING PRODUCT #670 Vinyl Ester Resin is packaged as follows: The "A" portion is packaged in 1-gallon, 5-gallon, and 55-gallon drums. The "B" portion is packaged in containers with sufficient catalyst (promoter) to be mixed with the 1-gallon.
MIXING For mixing quantities on the job site, mix 41 grams of “B” catalyst to one gallon “A” Resin.
APPLICATION PRODUCT #670 shall not be applied when surface temperatures are less than 32oF (0oC). Shelf life when stored at temperatures of 70oF is three months. When stored at temperatures of 32oF, it is six months. For best results, use one coat resin and set reinforced cloth into it with the use of an aluminum grooved roller. Apply a second layer of resin and cloth. When hardened to the touch, apply the last coat of resin, saturating the cloth, to produce a sealed surface.
LIMITATION Maximum continuous service temperatures is 180oF.
CAUTION DANGER! FLAMMABLE! Contains Styrene Monomer. Causes eye burns and skin irritation. Vapor irritating. Repeated or prolonged contact cause skin burns. Keep away from heat, sparks and flames. Keep container closed. Use with forced ventilation. Do not get into eyes. Avoid contact with skin and clothing. Avoid breathing vapor or mist. Wash thoroughly after handling. FIRST AID: In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Call a physician. Wash clothing before reuse. If swallowed, do not induce vomiting; drink 1 or 2 glasses of water or milk and call a physician. Never give anything by mouth to an unconscious person. In case of fire, use dry chemical foam or carbon dioxide. Flash Point: 92oF. Consult Material Safety Data Sheet for further safety information.
FOR INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN
| |||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2011 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products] [Where to Start] [Bonding Systems] [Chip Floors] [Chemical Resistance] [Epoxy.com Coatings] [Conductive Electrostatic Dissipative] [Applications] [Elastomeric Polyurethane Systems] [Garage Floors] [High Temperature] [Industrial Floors] [Epoxy and Urethane Injection of Concrete] [Joint Systems & Sealants] [Mortars / Grouts] [Methyl Methacrylate (MMA)] [Novolac Epoxy] [Polymer Systems] [Primers Sealers] [Misc.] [Seamless Flooring] [Waterproofing] [Dealers Wanted] [Installation Tips][Product Guide] [Wood Filler] [Who We Are] [Guide Specs][FAQs] [Tech Data Sheets in Acrobat Format] [Epoxy.com MSDS in Acrobat Format] [Epoxy.com Online Ordering Authorization Form]
|
