|
|
EpoxySystems'™ Product #701 Flexible Bonder
DESCRIPTION Epoxy Systems’ Product #701 Flexible Bonder is
a two component, 100% solids, mixed at a 1:1 ratio adhesive formulated to give
a permanent bond to ceramic, metal, concrete and elastomeric surfaces. Product
#701is thixotropic, non-sag, and is easily applied by trowel.
ADVANTAGES
SURFACE
PREPARATION Surface
must be clean. Remove grease, rust, or other foreign materials by best means
available. For best results surfaces should be dry during application. MIXING: Combine
one part by volume of Component “A” with one part by volume of Component
“B”. There are 231 cubic inches to a gallon. So you will get about 25.6
square feet per 1/16 inch of thickness. If using this as an anchor bolt, or dowel
bar adhesive, you can double check you volume with the
Epoxy.com Dowel Bar and Anchor Bolt Adhesive Calculator. CAUTION: WARNING!
A Component contains epoxy resin. DANGER! B Component contains alkaline
amines; strong sensitizer. May cause skin sensitization or other allergic
responses. Use with good ventilation, particularly if material is heated or
sprayed. Prevent all contact with skin or eyes. Wear protective clothing,
goggles, gloves, and/or barrier creams. Keep containers closed when not in
use. Wash thoroughly after handling. FIRST AID: In case of skin contact immediately wash with soap and water. In case
of eye contact, flush with copious amounts of water for at least (15) fifteen
minutes. Remove contaminated clothing. If irritation persists, seem medical
attention. Wash clothing before reuse. FOR INDUSTRIAL USE
ONLY KEEP AWAY FROM CHILDREN This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however,
is intended or made, nor is protection from any law or patent to be inferred,
and all patent rights reserved.1/00
| ||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
|
