|Tech Data Sheets in Acrobat Format | MSDS in Acrobat Format | Online- Ordering Authorization Form | Home

Epoxy.com #315NH is a 100%solids, moisture-insensitive epoxy coating. EPOXY.COM #315NH mixed at 2 :1 by volume ratio, produces an excellent coating for dry or damp concrete, wood, or steel surfaces. Epoxy.com #315NH is available in a summer grade and winter grade formulation. It can be used as a stand alone coating or as a base coat for Epoxy.com chip floor.

• Can be applied to concrete, wood, or primed steel.

• Has high gloss and is low viscosity.
• It does not have solvents and no solvent odor.
• Is available in a special winter grade formulation for fast setting applications down to 35° F.

WHERE TO USE:

To provide a tough, chemical and abrasion-resistant floor coating on concrete, wood or steel, which is easy to clean. Epoxy.com #315NH has a proven track record of successful use when applied to a properly prepared substrate. EPOXY.COM #315NH has been used for many other applications and is not limited to floors only.

Standard color is gray; to produce other colors, color chips must be submitted. Other colors are available

SURFACE PREPARATION:

For best results, areas to receive the Epoxy.com #315NH should be free of dirt, grease and heavy laitance, which will affect The bond. Shot blasting, sand blasting, water blasting or wire brushing are recommended for surface preparation. When used on steel, prime first with Epoxy.com #1200.

Combine two (2) parts of Component "A" and one (1) part Component "B", by volume, in the quantity desired and mix Epoxy.com #315NH with a low speed drill and Epoxy.com Mixing Paddle for three (3) to five (5) minutes. Avoid entrapping air while mixing. Apply immediately after mixing.

APPLICATION:

Apply by brush, roller, or spray. For best Results when spraying, strain material through a 60 mesh screen prior to spraying. Minimum recoat time with self is 6 hours, maximum recoat is 7days.

Epoxy.com #315NH will given an approximate coverage of 200 sq. ft./gallon at a thickness of eight (8) mils, when applied to a smooth surface; two (2) coats are recommended. Coverage will decrease when applied to a rough surface. Tack-free time is subject to ambient and surface temperatures.

PACKAGING:

Epoxy.com #315NH is packaged in three (3) gallon, fifteen (15) gallon, and 165 gallon units.

"A" Component contains epoxy resin.

DANGER! "B" Component contains alkaline amines; strong sensitizer. May cause skin

sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling.

FIRST AID: In case of skin contact, immediately wash with soap and water. In case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing shoes. If irritation persists, seek medical attention. Wash clothing before reuse.

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 300 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826  Technical Support
                         Norm Lambert, President - Technical Support Director 
                         info@epoxy.com
  
352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com 

352-489-1625   Fax line to all Departments
 
www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

Copyright © 1994-2008 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;  Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight  Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days.   ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis.   Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater.  No returns on non-list priced items.  All Returns are for merchandise (store) credit only, no cash or credit card credits.  In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

[Technical Data Sheets in Adobe Acrobat Format][MSDSs in Adobe Acrobat Format][Online- Ordering Authorization Form]

Secure Login