Epoxy.com Product #315BC
100% Solids High-Build Polymeric Coating
Epoxy.com Product #315BC High-Build Polymeric Coating is a two component, 100% solids polymeric Hi-Build polymeric coating used for high foot
and light forklift traffic areas where abrasion resistance is required; for
protection against mild corrosion; and as a decorative waterproof coating for
walls, floors, tanks, pools etc. Also used as a base coat for
- Moisture Insensitive
- Ceramic like finish
- Solvent Free
- Extremely Durable
- Chemical Resistant
Surface to receive
Epoxy.com Product #315BC High-Build Polymeric Coating
must be clean and sound. Remove all dirt, laitance, grease curing compounds
and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast
immediately prior to application.
Temperature of Epoxy.com Product #315BC High-Build Polymeric Coating (normal cure) must be 50° F or above at time of mixing. Stir each
component separately before blending. Mix two parts by volume of Part A with
one part by volume of Part B for three
minutes with a low speed electric drill motor equipped with a mixing paddle.
ApplyEpoxy.com Product #315BC High-Build Polymeric Coating with a roller, brush, or spray equipment. When not used as
part of the 315 Chip Flooring System, 2 coats are recommended. Thickness per coat should be 7-10
mils. Seven days cure time is required to reach maximum chemical resistance.
When installing over concrete Product #899 or Product #203 Primer is
DO NOT apply Epoxy.com Product #315BC High-Build Polymeric Coating at temperatures below 50° F. Surface must be dry.
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash
immediately and seek medical help. Use safety glasses with side shields and
wear protective rubber gloves.
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or
any lacquer solvent
APPLICATION PROPERTIES @77°F
(200 gr.) in minutes @70° F.
in Hours @ 70° F.
||3 gallon units (2 gallons of "A" + 1 gallon of "B"
White, Light Gray, Dark Gray, Taupe, Sand,
Gold, Mocha, Brick Red, Slate Blue,
Colonial Green, Deep Blue,
Black, Safety Yellow
Click the picture
of color card below for a larger version of this picture
of the color chart.
The picture to the right is a photographic reproduction of the
color card for this product. The photo reproduction process and your
monitor and/or printer will change these colors. This chart is to give you
an idea of the colors available and not intended for critical color selections.
Material Certification of LEED Requirements
Epoxy.com a division of Epoxy Systems, Inc. certifies that Epoxy.com meet or exceed LEED requirements as summarized below:
LEED Credit IE 4.2:
Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 4.2 Indoor Emitting Materials Credit. Refer to the individual product component
technical data sheets and MSDS for further information.
Other customers who visited this page also visited:
For more information please contact:
A Division of
Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems
Since 1980 - Over 33 years
Florida & Vermont
Customer and Technical Support Hours: 9AM-4PM Eastern Time
(6AM-1PM Pacific Time)
Closed 12 Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order
Katey Fontaine, VP - Customer
352-533-2167 Norm Lambert, President - Technical
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
We accept MasterCard, Visa, American Express,
Discover, or Wire Transfers.
Copyright © 1994-2019
a division of
Epoxy Systems, Inc.
- Florida and Vermont. All rights reserved.