Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Product Application Guide

Commonly used RESINS


 Primers & Sealers

Back to Table of Contents

Epoxy.com Heavy Duty Industrial Epoxy and Urethane Coating Resin Systems

Here are listing of Epoxy.com epoxy coatings and urethane coatings. The Epoxy.com Products listed below are either pigmented or available in pigmented.  Related products not specifically covered below are Primers and Sealers, and  Flooring and Decking Systems

Solvented Coatings
Water Based Coatings
General Purpose 100% Solids "0" VOC Epoxy Coatings
100% Solids Heavy Duty Industrial Floor Coatings
Fast Setting Epoxy and Low Temperature Cure Epoxy
Chemical Resistant Epoxy - Novolac
Chemical Resistant Epoxy - other
High Temperature Epoxy

High Temperature High Chemical Resistant Epoxy
Coal Tar Epoxy Coatings
Conductive Epoxy and Conductive Urethane Coatings
Polyurethane Coatings -non conductive
Specialty Epoxy Coatings - Epoxy Coatings that don't fit into the above categories
Coating Calculator - Calculate how much Epoxy.com coating you will need for your job.

Solvented Coatings

Water Based Coatings

  • Product #231 - Water Based Epoxy Emulsion Primer and Sealer is a water based epoxy primer/sealer designed to have maximum resin penetration into concrete surfaces to provide high bond strength and adhesion. Product #231 Water Based Epoxy Emulsion Primer and Sealer has very low odor and, therefore, can be used in occupied areas. Product #231 Water Emulsion Primer and Sealer has the ability to be applied to recently poured (green) concrete and achieve excellent adhesion. Product #231 Water Emulsion Primer and Sealer is ideal for both new and old concrete surfaces. It is used as a primer for High Build and Thin Film Coating Systems.
  • Epoxy.com Product #675 Electrostatic Dissipating Water Borne Epoxy Topcoat is a pigmented, water emulsion epoxy electro-static dissipative finish designed to have maximum penetration into concrete surfaces to provide high bond strength and adhesion. It has very low odor and can be used in occupied areas as a finish sealer in Thin-Film Electro-Static Dissipative Coating Systems.

100% Solids "0" VOC Epoxy Coatings

  • Epoxy.com Product #1 All Purpose Coating  is a 100% solids epoxy Hi-Build epoxy coating used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, etc . Also available fast, and Cold Temperature Cure versions.
  • Epoxy.com Product #1W is a two component, 100% solids epoxy Hi-Build epoxy coating used for high indoor traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, tanks, etc.

General Purpose 100% Solids Heavy Duty Industrial Floor Coatings

Fast Cure Epoxy and Low Temperature Cure Epoxy

  • Epoxy.com Product #1 Fast  - is a shorter potlife, and faster setting version of Epoxy.com Product #1,
  • Epoxy.com Product #1 Cold Temperature Cure  is a version of Epoxy.com Product #1 that sets even faster than Product#1 Fast.  Typically used in colder temperatures, or where an very fast cure is required.
  • Epoxy.com Product #2 Fast  is a  shorter potlife, and faster setting version of Product #2
  • Epoxy.com Product #2 Cold Temperature Cure & is a version of that sets even faster than Epoxy.com Product#2 Fast Cure.  Typically used in colder temperatures, or where an very fast cure is required.
  • Epoxy.com Product #204 Cold Temperature Cure Polymeric Coating -   is a specially formulated coating for cold temperature applications. Able to cure at temperatures as low as 35�F. It is often used in coolers and food preparation areas that require constant low temperatures. It is also frequently used in room temperature applications to meet super-fast cure, limited shutdown needs.

Chemical Resistant Novolac Epoxy

  • Epoxy.com Product #630 Novolac Coating/Mortar Binder - a 100% solids epoxy Novolac ideal for harsh chemical and solvent resistant applications. It is ideal for use as a troweled mortar, slurry binder, and coating for concrete and steel in extremely corrosive areas where resistance to 98% sulfuric acid or other strong caustics is needed. Epoxy.com Product #630 Novolac Coating/Mortar Binder is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities.
  • Epoxy.com Product #633 Novolac Coating is a 100% solids epoxy Novolac coating ideal for harsh chemical and solvent resistant applications. It is used in secondary containment, solvent storage, pump pads, trenches, and other high exposure areas. It is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities. Epoxy.com Product #633 Novolac Coating is commonly used as a seal coat for Epoxy.com MORTAR SYSTEMS where chemical resistant performance is required. 

Chemical Resistant Epoxy -Other

  • Epoxy.com Product #2 Chemical Resistant Coating  is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications. Available in normal, fast, and Cold Temperature Cure. Also available fast, and Cold Temperature Cure versions.
  • Epoxy.com Product #2W Chemical Resistant Wall Coating   is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications.

High Temperature

Product #661 Vinyl Ester Binder Adhesive is a clear, 100% reactive, vinyl ester novolac used to coat or line concrete or steel surfaces in chemically aggressive industrial environments. It is used for coating primary and secondary containment, trenches, troughs, pump pads, and equipment.

Product #662 Vinyl Ester Aggregate

Product #663 Vinyl Ester Coating is a 100% reactive, vinyl ester novolac used to coat concrete or steel surfaces in chemically aggressive industrial environments. Due to its high molecular weight and low permeability, it will withstand exposure to bond range of acids, caustiec and solvents. It is designed as a coating for secondary containment, trenches, troughs, pump pads, equipment and structural members. Low Temperature accelerators are available for positive cure at temperatures down as low as 33� F.

Coal Tar Epoxy Coating

Coal Tar Epoxy Product #209 is a two component 100% solids epoxy coating designed for applications to petroleum contaminated concrete, coating asphalt based surfaces, clean concrete, cement, and properly prepared steel.

Conductive Epoxy Coatings

Polyurethane Coatings

Specialty Coatings - Not listed above

Back to Table of Contents

Epoxy.com Seamless Industrial Epoxy Flooring

Flooring
Accessories and Fillers

Products Typically Used for Epoxy.com Flooring

Most of Epoxy.com Coatings can also be used to make seamless floors. Some of the Seamless Flooring Systems below will also benefit from the use of a Primer. Contact Epoxy.com Technical Support for details.

Methyl Methacrylate - MMA

 

Products typically as Epoxy.com Flooring Accessory Products and Fillers

Proper mixing and installation is critical to the optimal success of all products.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA

We have products that have passed the test of time as well as the best new Systems available today.

Since 1980 - 40 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM


321-206-1833  Customer Service - Ordering and Order Status
                         Katey Lambert-Fontaine, VP - Chief Operations Officer
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

Copyright © 1994-2023 (providing online information about the right product for the right job for nearly 30 years)  EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.