Epoxy.com Product #27

Slow Setting Mortar Pack

DESCRIPTION

Epoxy.com Product #27 Grout/Mortar Pack is a preproportioned 100% solids epoxy resin pack and a blend of special aggregate. The pot life of Product #27 is 3 times longer than ordinary epoxy packs; while curing the entire pack, a low exotherm is produced.

ADVANTAGES

Premeasured to avoid waste while mixing and placing.
Moisture insensitive before and after cure.
Pourable viscosity - flows easily, self levels in forms.
Low heat build-up - low exothermic heat development permits placement up to 10 inches thick.
High ultimate compressive strength
High ultimate Modulus of Elasticity - 2.7 X 10⁶ psi
No curling or shearing away from substrate (concrete, steel or wood).

WHERE TO USE

Use in areas where long pot life and extended working time are required due to higher than normal temperatures or when placement of an epoxy grout is slow.

PHYSICAL PROPERTIES

Viscosity after mixing:	Pourable
Pot Life: 70°F (21°C)	1 hr. 45 min.
Pot Life: 102°F (39°C)	1 hr. 15 min.
Compressive Strength ASTM C-109 M 28 days	9,500
Modulus of Elasticity	2,700,000 psi
Electrical Properties Volume Resistivity ASTM D-257	3.03 X 10¹² ohm-cm

MIXING

Pour Component 'A' into Component 'B'. Mix 2 to 3 minutes. Pour mixed material into container large enough to accommodate 77 lbs. of filler and resin. Mix slowly for 3 to 5 minutes until homogeneous mix, gray in color, is achieved.

Note: Do not thin. Solvents will prevent proper cure.

SURFACE PREPARATION

Substrate must be clean and sound. Remove all laitance, oil, and grease by sandblasting, wire brushing, or bush hammering. When used on steel, remove mill scale, rust or any other contaminants and wipe surface clean with approved metal cleaning solvent.

Patching: Clean out defective area and patch with Epoxy.com Product #27 and allow to cure before put into use.

Forming: Epoxy.com Product #27 is a self-leveling material. Seal forms to prevent seepage. Wax inside of forms or use bond-breaking liner to prevent adhesion of grout to form.

APPLICATION

Epoxy.com Product #27 may be placed in single or multiple lifts up to 10 inches thick. Apply at ambient temperatures as low as 50°F. Exposure to elevated temperatures for prolonged periods is not recommended. (Use Epoxy.com Product #641LV Heat Resistant Grout up to 400°F).

PACKAGING

Component "A" is packaged in a 1-gallon can (92.7 fluid oz.)
Component "B" is packaged in a 1/2-gallon can (64 fluid oz.
Component "C" Aggregate is in an 77 lb. bag
Actual yield: .635 cubic feet of grout.

SHELF LIFE

Two (2) years in closed container

CAUTION:

WARNING! A Component contains epoxy resin. May cause skin sensitization or other allergic responses. Avoid inhalation of vapor. Use good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves, and/or barrier creams. If contact with skin occurs, wash immediately with soap and water. In case of contact with eyes, flush immediately with water and contact a physician.

CAUTION! DANGER "B" component Contains Alkaline Amines. May cause severe burns, strong sensitizer. Do not get into eyes, on skin, or clothing. Avoid breathing vapor. Keep container closed. Use with adequate ventilation. Wash thoroughly after handling.

FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.

Epoxy.com Home Page

Product Catolog

Important Links

Untitled Page

Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over 375 products,
Since 1980
Florida & Vermont
USA

Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch.

321-206-1833   Customer Service - Ordering and Order Status
                          Katey Fontaine, VP - Customer Service Director
                          sales@epoxy.com

714-657-3826 Technical Support
                         Norm Lambert, President - Technical Support Director
                         info@epoxy.com

352-489-1666   Accounting and Administration
                          Debby Lambert, CEO, and CFO
                          office@epoxy.com

352-489-1625 Fax line to all Departments

www.epoxy.com

24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253

Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping.

This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved.

Epoxy Systems™ Product Company ("ESI") warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. ESI warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of ESI. If any product fails to meet this warranty, the liability of ESI will be limited to replacement of any non-conforming material if notice of such non-conformity is given to ESI within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). ESI may in its discretion refund the price received by ESI in lieu of replacing the material. No customer, distributor, or representative of ESI is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of ESI. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. ESI reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. ESI'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND ESI SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability.

Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.

[Technical Data Sheets in Adobe Acrobat Format][MSDSs in Adobe Acrobat Format][Online- Ordering Authorization Form]

Hit Counter

Secure Login